26 February 2021 in Technology audit and production reserves
The object of research is the efficiency of dust collection of fine dust in an apparatus with an intense turbulent mode of phase interaction. One of the most problematic areas of the existing dust and gas cleaning equipment is the low efficiency of collecting fine dust. Effective cleaning of exhaust gases from dust involves the use of multi-stage cleaning systems, including wet and dry dust cleaning devices, which entails high capital and operating costs. These disadvantages are eliminated in the developed design of the cyclone-vortex dust collector with two contact zones. The device implements both dry and wet dust collection mechanisms, which allows for high efficiency of dust removal at high productivity. The conducted studies of the total and fractional efficiency of dust collection when changing the operating parameters of the developed device showed that the efficiency of collecting fine dust is 98–99 %. The increase in the efficiency of dust collection in the dry stage of the device is due to an increase in centrifugal force. In the wet stage of contact, the efficiency reaches its maximum values due to the vortex crushing of the liquid in the nozzle zone of the apparatus. Studies of the fractional efficiency of the apparatus show that with an increase in the diameter of the captured particles, the efficiency of the dust collection process for dry and wet stages, as well as the overall efficiency, increases. With an increase in the density of irrigation, the overall efficiency of dust collection in the apparatus increases. It has been established that an increase in the efficiency of capturing highly dispersed particles occurs due to turbulent diffusion, the value of which is determined by the frequency of turbulent pulsations and the degree of entrainment of particles during the pulsating motion of packed bodies. To describe the results obtained, a centrifugal-inertial model for a dry contact stage and a turbulent-diffusion model of solid particle deposition for a wet contact stage are proposed, which make it possible to calculate the dust collection efficiency of the contact stages, as well as the overall efficiency of the cyclone-vortex apparatus. The results obtained show the prospects of using devices of this design at heat power plants and other industries.
1 November 2020 in Series of Geology and Technical Sciences
For separation of plastic wastes (polyamide (PA), acrylonitrile butadiene styrene (ABS) and polystyrene (PS), a flotation method is proposed. Using this method, the effect of concentration of surface-active substances (surfactants), which were used as polidocanol, sulphanole and a mixture of surfactants containing sodium laureth sulfate and diethanolamide, was studied. The research results analysis of the flotation separation of a mixture of crushed plastic wastes was carried out according to the calculated values of the extraction of a floated component c and the purity of a concentrate beta. It was noted that the maximum extraction of the floated component depends on the polymer and surfactant type. A mixture of surfactants at lower concentrations allows to achieve greater extraction of the floated component with less foaming ability. The research results on the extraction of polystyrene from the air flow rate at various concentrations of surfactants' mixture show that the extraction has a maximum at a certain air flow rate. At low air flow rates, the working volume of liquid is not saturated enough with gas bubbles. If the optimal value of air flow rates is exceeded, many gas bubbles are formed that are not involved in the flotation process. The research results on the extraction of polystyrene from the aerated liquid layer height at various concentrations of surfactants' mixture show that, at a low height of the aerated liquid layer, the probability of collision of a plastic particle with an air bubble is low and some potentially floated particles seek the bottom of an apparatus without having time to collide with an air bubble. When assessing the influence of liquid temperature on the flotation process, it was found that increasing the liquid temperature above 20 degrees C leads to a sharp decrease in ABS and PS extraction. This is explained by the fact that the dependence of the surfactants' foaming ability on the temperature is characterized by solubility curves and for most surfactants they have an extremum.
1 July 2026 in Eurasian Journal of Applied Engineering and Technology (EJAET)
Рассмотрены конструкции аппаратов с трубчатой насадкой регулярной структуры с внешним и внутренним расположением коллекторов и на основе анализа их работы нами создан аппарат с регулярной насадкой, выполненной в виде системы непрерывно и последовательно соединенных труб одного диаметра внутри корпуса аппарата. Основываясь на известном подходе движения газа по извилистым каналам, получены уравнения для расчета порозности трубчатой насадки из непрерывно соединенных труб в сечении аппарата, объемной порозности и эквивалентного диаметра, учитывающие конструктивные составляющие трубчатого пучка и шаги размещения труб в вертикальном и радиальном направлениях. Проведено сопоставление расчетных данных конструктивных параметров для трубчатых насадок с прямыми трубами и выносными коллекторами и непрерывно соединенных труб, которые показали, что присутствие отводов в пучке из непрерывно соединенных труб приводит к снижению численных значений объемной порозности и эквивалентного диаметра за счет уменьшения свободного пространства контактной зоны.
30 September 2024 in Mechanics and Technologies
The use of known designs of irregular and regular stationary nozzles, movable and regularly movable nozzles has been analyzed, their shortcomings have been identified and ways of their modernization have been established. An experimental study of the hydraulic resistance of a packed layer with rotating packed elements with rectangular blades was carried out when changing the location steps in the vertical and radial directions. It is noted that when changing the vertical step, it is possible to achieve an in-phase regime, characterized by an increase in the power of the formed vortices, which has a beneficial effect on achieving a highly developed interphase surface and the efficiency of the processes being carried out. The presence of a critical step is confirmed when the distances between adjacent packings in the same row in the radial direction change, at which a restructuring of the vortex formation mechanism occurs. The frequency of vortex formation before the critical step is determined by the size of the gap between adjacent packed elements in a row, and after it by the width of the streamlined elements. An equation has been obtained for calculating the hydraulic resistance of an apparatus with rotating packed elements with rectangular blades, which takes into account the processes of formation and interaction of vortices behind the packed elements and characterizes the energy consumption in the heat and mass transfer apparatus.
15 June 2020 in SERIES CHEMISTRY AND TECHNOLOGY