7 August 2014 in PLOS ONE
Salidroside is one of the major phenolic glycosides in Rhodiola, which has been reported to possess various biological activities. In the present study the in vivo deglycosylation metabolism of salidroside was investigated and its aglycone p-tyrosol but not the original salidroside was identified as the main form in rat tissues following the administration of salidroside. After the i.v. administration of salidroside at a dose of 50 mg/kg in rats, salidroside was quantified only in the liver, kidney and heart tissues. The highest level of p-tyrosol was detected in the heart, followed by the spleen, kidney, liver and lungs, in order. Salidroside was detected only in the liver, in contrast, p-tyrosol was detectable in most tissues except the brain, and the kidney tissues contained a significant amount of p-tyrosol compared to the other tissues after the i.g. administration of 100 mg/kg salidroside. The excretion behaviour revealed that the administrated salidroside mainly eliminated in the form of salidroside but not its aglycone metabolite p-tyrosol through urine. After i.v. and i.g. administration in rats, 64.00% and 23.80% of the total dose was excreted through urine in the form of salidroside, respectively. In addition, 0.19% and 2.25% of the dose was excreted in the form of p-tyrosol through urine after i.v. and i.g. administration, respectively. The faecal salidroside and p-tyrosol concentrations were 0.3% and 1.48% of the total dose after i.v. administration, respectively. After the i.g. administration of salidroside, trace salidroside and p-tyrosol were quantified in faeces within 72 h. In addition, the biliary excretion levels of salidroside after i.v. and i.g. administration were 2.86% and 0.02% of the dose, respectively. The obtained results show that salidroside was extensively metabolised to its aglycone p-tyrosol and distributed to various organs and the orginal salidroside was cleared rapidly through urine following the administration of salidroside.
12 August 2022 in Ocean Engineering
20 May 2023 in Ocean Engineering
1 October 2022 in Ocean Engineering
1 November 2022 in Physics of Fluids
Tail cavities are common in gas-propelled underwater cold emission and jet-propelled underwater vehicles. They can also provide a stable working environment for solid rocket motors. In this study, a 2 mm diameter ventilation hole was provided at the vehicle's rear for a ventilation-induced cavity. Then, the effect of different initial ventilation flows (Q) and Froude numbers (Fr) on cavity collapse after the air supply was stopped was studied. Three different tail cavity closure types are observed: the intact cavity (IC), partially broken cavity (PBC), and pulsating foam cavity (PFC). The IC changes from a twin vortex tube closure to a re-entrant jet closure, eventually collapsing entirely. The cavity collapse time decreases with increasing Fr and increases with increasing Q. The dimensionless cavity length (L/D) has an exponential relationship with time when Fr is small and becomes linear with time when Fr is large. The cavity collapse velocity increases with increasing Fr, while Q has little effect. For PBC collapses, the cavity first transforms into an IC and then collapses as an IC. L/D first increases to a local maximum and then decreases. The effect of the reflux gas on the cavity length is critical. During PFC collapses, the cavity first transforms into a PBC, then into an IC, and finally collapses as an IC. L/D first increases to a local maximum and then decreases exponentially.
1 August 2022 in Physics of Fluids
The high-pressure capture wing (HCW) configuration has excellent aerodynamic characteristics verified by theoretical, experimental, and numerical simulation methods. It has a good effect on improving vehicle lift at hypersonic speed. A HCW-V configuration based on the HCW was proposed in this paper. This configuration further increased the vehicle's lift by increasing the wedge angle of the capture wing and forming a compression plane on the lower surface. We obtained the pressure ratio relationship between the upper and lower surfaces of the HCW-V configuration concerning the free-stream airflow Mach number, the body compression angle, and the captive wing wedge angle based on theoretical derivation. It was nearly 60% higher than the HCW configuration pressure ratio. In addition, the influence of the HCW-V configuration on the vehicle's aerodynamic characteristics at different Mach numbers and body compression angles was studied through numerical simulation methods. The HCW-V configuration improved the lift-to-drag ratio by at least 25% compared with the HCW configuration. The expression of the lift coefficient of the vehicle CL = −0.095Ma∞tanδ + 2.352tanδ + 0.031θ + 0.010 under the model presented was obtained in this study. Meanwhile, the adaptability of this configuration to varied Mach number and attack angle was investigated further. The average lift-to-drag ratio of HCW-V was increased by 23.7% and 7.09% at varying Mach numbers and angles of attack. The lift-to-drag ratio of the three-dimensional HCW-V configuration is 14% higher than that of the HCW configuration when the wedge angle is 4.19°.