Bhaskar Kathirvelu

Bhaskar Kathirvelu

Auto-generated profile, based on publicly available information

Bhaskar Kathirvelu

Rajalakshmi Engn Coll, Dept Automobile Engn, Chennai 602105, Tamil Nadu, India

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

30 September 2016 in Journal of Mechanical Engineering and Sciences
Verified
Journal Article
Closed access
KBK. Bhaskar
K. Bhaskar
Sendilvelan SubramanianSendilvelan Subramanian
Sendilvelan Subramanian
VMV. Muthu
V. Muthu
SAS. Aravindraj
S. Aravindraj

24 October 2013 in International Journal of Green Energy
Verified
Journal Article
Closed access
KBK. Bhaskar
K. Bhaskar
GNG. Nagarajan
G. Nagarajan
SSS. Sampath
S. Sampath

1 January 2016 in International Journal of Energy for a Clean Environment
Verified
Journal Article
Closed access
PDF file
Sendilvelan SubramanianSendilvelan Subramanian
Sendilvelan Subramanian
KBK. Bhaskar
K. Bhaskar
The factors to be considered while designing a new combustion process are a higher compression ratio, lean homogeneous air–fuel mixture, complete combustion and instantaneous combustion, which leads to Homogeneous Charge Compression Ignition (HCCI). HCCI is a clean and efficient combustion process. In this work, an attempt has been made to experimentally analyze the performance and emission characteristics of the HCCI process with Premixed Charge Compression Ignition (PCCI) mode assisted with pilot injection as a combustion initiator. Experiments were conducted in a modified single cylinder water-cooled diesel engine employing a conceptual system known as transient state fuel induction with different fuels such as diesel, petrol, and bio-diesel and it was observed that there was a reduction in the emission level of carbon monoxide and hydrocarbon with the same power output as in the conventional diesel engine. At full load, the carbon monoxide emissions of various tested modes varied from 0.2% to 0.32%, the hydrocarbon of various modes tested varied from 11 ppm to 28 ppm, and the smoke emissions of various modes tested varied from 7 mg/m3 to 10 mg/m3.

1 January 2013 in International Journal of Green Energy
Verified
Journal Article
Closed access
KBK. Bhaskar
K. Bhaskar
GNG. Nagarajan
G. Nagarajan
SSS. Sampath
S. Sampath
In diesel engines simultaneous reduction of NOx and Particulates (PM) is a challenging task for researchers. Different strategies, such as retarding injection timing, increasing injection pressure, employing common rail fuel injection system, pilot injection, multi-injection, pre-mixed charge compression ignition (PCCI), Homogeneous Charge Compression Ignition (HCCI), EGR, and after treatment devices are adopted to reduce the NOx and PM emissions. In this work an attempt is made to reduce NOx and PM using partially premixed charge compression ignition (PPCCI) combustion mode with diesel as fuel in a single cylinder diesel engine. Part of the fuel is injected into the intake manifold to form homogeneous premixture beforehand and the premixture is burnt in the cylinder with the balanced quantity of fuel directly injected into the cylinder by a conventional injection system. The premixed fuel ratio (Rp) was varied from 25%, 50%, and 75%. The Premixed ratio (Rp) is defined as the ratio of the energy of premixed fuel to the total energy supplied. Due to homogenous lean operation, significant reductions of NOx and smoke are achieved.

7 May 2001 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
Sendilvelan SubramanianSendilvelan Subramanian
Sendilvelan Subramanian
KJK. Jeyachandran
K. Jeyachandran
KBK. Bhaskar
K. Bhaskar
This paper deals with the development and performance of the Electrically Heated Catalytic (EHC) converter with copper oxide as a catalyst in a spark-ignition (SI), gasoline-fueled engine. It is found that the EHC reduces cold-start hydrocarbon (HC) and carbon monoxide (CO) emission, when used with existing catalytic converter. From this, the potential of catalytic systems with copper oxide as catalyst is analyzed. Various parameters have been analyzed with the available experimental data, with the help of multiple regression analysis. It is found that the agreement between the analyzed and experimental result is satisfactory. Therefore, it is concluded that, the equation developed in this study can be used with confidence to analyze the emission performance.