1 November 2000 in Journal of Biomechanics
8 February 2008 in Science
We have developed a biomechanical energy harvester that generates electricity during human walking with little extra effort. Unlike conventional human-powered generators that use positive muscle work, our technology assists muscles in performing negative work, analogous to regenerative braking in hybrid cars, where energy normally dissipated during braking drives a generator instead. The energy harvester mounts at the knee and selectively engages power generation at the end of the swing phase, thus assisting deceleration of the joint. Test subjects walking with one device on each leg produced an average of 5 watts of electricity, which is about 10 times that of shoe-mounted devices. The cost of harvesting—the additional metabolic power required to produce 1 watt of electricity—is less than one-eighth of that for conventional human power generation. Producing substantial electricity with little extra effort makes this method well-suited for charging powered prosthetic limbs and other portable medical devices.
1 April 2005 in Exercise and Sport Sciences Reviews
Walking like an inverted pendulum reduces muscle-force and work demands during single support, but it also unavoidably requires mechanical work to redirect the body’s center of mass in the transition between steps, when one pendular motion is substituted by the next. Production of this work exacts a proportional metabolic cost that is a major determinant of the overall cost of walking.
1 December 2002 in Journal of Experimental Biology
SUMMARY: In the single stance phase of walking, center of mass motion resembles that of an inverted pendulum. Theoretically, mechanical work is not necessary for producing the pendular motion, but work is needed to redirect the center of mass velocity from one pendular arc to the next during the transition between steps. A collision model predicts a rate of negative work proportional to the fourth power of step length. Positive work is required to restore the energy lost, potentially exacting a proportional metabolic cost. We tested these predictions with humans (N=9) walking over a range of step lengths(0.4-1.1 m) while keeping step frequency fixed at 1.8 Hz. We measured individual limb external mechanical work using force plates, and metabolic rate using indirect calorimetry. As predicted, average negative and positive external mechanical work rates increased with the fourth power of step length(from 1 W to 38 W; r2=0.96). Metabolic rate also increased with the fourth power of step length (from 7 W to 379 W; r2=0.95), and linearly with mechanical work rate. Mechanical work for step-to-step transitions, rather than pendular motion itself, appears to be a major determinant of the metabolic cost of walking.
17 September 2001 in Journal of Biomechanical Engineering
We modified an irreducibly simple model of passive dynamic walking to walk on level ground, and used it to study the energetics of walking and the preferred relationship between speed and step length in humans. Powered walking was explored using an impulse applied at toe-off immediately before heel strike, and a torque applied on the stance leg. Although both methods can supply energy through mechanical work on the center of mass, the toe-off impulse is four times less costly because it decreases the collision loss at heel strike. We also studied the use of a hip torque on the swing leg that tunes its frequency but adds no propulsive energy to gait. This spring-like actuation can further reduce the collision loss at heel strike, improving walking energetics. An idealized model yields a set of simple power laws relating the toe-off impulses and effective spring constant to the speed and step length of the corresponding gait. Simulations incorporating nonlinear equations of motion and more realistic inertial parameters show that these power laws apply to more complex models as well.
7 October 2001 in Proceedings Of The Royal Society B-Biological Sciences
We studied the selection of preferred step width in human walking by measuring mechanical and metabolic costs as a function of experimentally manipulated step width (0.00–0.45L, as a fraction of leg length L). We estimated mechanical costs from individual limb external mechanical work and metabolic costs using open circuit respirometry. The mechanical and metabolic costs both increased substantially (54 and 45%, respectively) for widths greater than the preferred value (0.15–0.45L) and with step width squared (R2 = 0.91 and 0.83, respectively). As predicted by a three-dimensional model of walking mechanics, the increases in these costs appear to be a result of the mechanical work required for redirecting the centre of mass velocity during the transition between single stance phases (step–to–step transition costs). The metabolic cost for steps narrower than preferred (0.10–0.00L) increased by 8%, which was probably as a result of the added cost of moving the swing leg laterally in order to avoid the stance leg (lateral limb swing cost). Trade–offs between the step–to–step transition and lateral limb swing costs resulted in a minimum metabolic cost at a step width of 0.12L, which is not significantly different from foot width (0.11L) or the preferred step width (0.13L). Humans appear to prefer a step width that minimizes metabolic cost.