21 December 2007 in Physical Review B
Combined experimental and theoretical investigations on thin films of pentacene are performed in order to determine the structure of the pentacene thin film phase. Grazing incidence x-ray diffraction is used for studying a pentacene thin film with a nominal thickness of . The crystal structure is found to exhibit the lattice parameters , , , , , and . These crystallographic unit cell dimensions are used as the only input parameters for ab initio total-energy calculations within the framework of density functional theory revealing the molecular packing within the crystal structure. Moreover, we calculate the electronic band structure of the thin film phase and compare it to that of the bulk phase. We find the intermolecular bandwidths of the thin film phase to be significantly larger compared to the bulk structure, e.g., the valence bandwidth is twice as large. This remarkable effect is traced back to an enhanced intermolecular overlap due to the upright standing molecules in the thin film phase.
31 May 2019 in Journal of Applied Crystallography
GIDVisis a software package based on MATLAB specialized for, but not limited to, the visualization and analysis of grazing-incidence thin-film X-ray diffraction data obtained during sample rotation around the surface normal.GIDVisallows the user to perform detector calibration, data stitching, intensity corrections, standard data evaluation (e.g.cuts and integrations along specific reciprocal-space directions), crystal phase analysisetc. To take full advantage of the measured data in the case of sample rotation, pole figures can easily be calculated from the experimental data for any value of the scattering angle covered. As an example,GIDVisis applied to phase analysis and the evaluation of the epitaxial alignment of pentacenequinone crystallites on a single-crystalline Au(111) surface.
6 November 2009 in The Journal of Physical Chemistry Letters
3 November 2011 in Physical Chemistry Chemical Physics
Colloid probe atomic force microscopy has been used to study the nanotribological properties of the silica–ethylammonium nitrate (EAN)–mica system. Normal force curve measurements reveal a series of steps at separations that are consistent with the size of an EAN ion pair (0.5 nm) due to displacement of structured solvent layers as the two surfaces are brought together. At closest separations, two steps are measured with widths of 0.3 nm and 0.1 nm, which are too small to be due to an ion pair layer. The 0.3 nm step is attributed to a partial displacement of a silica-bound cation-rich layer, with residual cations being removed in the subsequent 0.1 nm step. Lateral force measurements reveal that the frictional response is dependent on the number of ion pair layers between the surfaces. At low forces, when there is more than a single layer of EAN between silica and mica, the lateral force increases relatively steeply with applied load, and is independent of the sliding speed. At intermediate forces, a single layer of cations in an intercalated bilayer structure is present between the surfaces. The friction coefficient (μ) increases logarithmically with sliding speed consistent with an activated, discontinuous sliding process. At high force, μ is small and once again, independent of sliding velocity. The adsorbed cation layer is bound primarily to mica and compressed by the high normal force. This robust layering with a well-defined sliding plane permits the colloid probe to slide easily over the mica surface.
21 January 2019 in Soft Matter
Control over drug delivery may be interestingly achieved by using temperature responsive encapsulants, which change their thickness and mesh size with temperature. The prototype N-isopropylacrylamide hydrogel cross-linked with di(ethylene glycol) divinyl ether p(NIPAAm-co-DEGDVE) swells at low temperature and collapses above the lower critical solution temperature (LCST), ∼29 °C in a buffer. It might be expected that drug release from such encapsulation is always favored below the LCST, due to the larger free volume present in the swollen polymer film. Recent results show contradicting behavior where some cases behave as expected and others release much less when the polymer layer is swollen. In this study, layers of the drugs phenytoin, clotrimazole and indomethacin were drop cast on glass and p(NIPAAM-co-DEGDVE) layers were then synthesized directly on top of these drug layers via initiated chemical vapor deposition (iCVD), a solvent-free and gentle polymerization technique. Dissolution experiments were then performed, in which the drug release through the hindrance of the hydrogel was measured at different pH values. The results show that not only the swelling but also the permeate (drug in this case)–polymer interaction plays an important role in the release.