Gulsen Baytemir

Gulsen Baytemir

Auto-generated profile, based on publicly available information

Gulsen Baytemir

Department of Physics Middle East Technical University Ankara 06800 Turkey

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2019 in Solar Energy
Verified
Journal Article
Closed access
GBGulsen Baytemir
Gulsen Baytemir
ECE. Hande Ciftpinar
E. Hande Ciftpinar
RTRasit Turan
Rasit Turan

27 February 2017 in Physica Status Solidi (RRL) – Rapid Research Letters
Verified
Journal Article
Closed access
PDF file
GBGulsen Baytemir
Gulsen Baytemir
FEFirat Es
Firat Es
AAArif Sinan Alagoz
Arif Sinan Alagoz
RTRasit Turan
Rasit Turan

1 February 2020 in Renewable Energy
Verified
Journal Article
Closed access
FEFırat Es
Fırat Es
ESEmel Semiz
Emel Semiz
EOEfe Orhan
Efe Orhan
EGEzgi Genç
Ezgi Genç
GKGamze Kökbudak
Gamze Kökbudak
RTRaşit Turan
Raşit Turan

25 June 2018 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
ATAshkan Vakilipour Takaloo
Ashkan Vakilipour Takaloo
FEFırat Es
Fırat Es
GBGülsen Baytemir
Gülsen Baytemir
RTRaşit Turan
Raşit Turan
The texturing of silicon surfaces is a well-known method of reducing the reflection from the surface of crystalline Si solar cell devices. With the utilization of diamond wires in recent advances in wafer slicing technology, surface texturing for the multi-crystalline Si wafers by the traditional acid-based texturing technique has become difficult. Metal-Assisted Etching (MAE) has been shown to be a promising and low-cost alternative to the traditional acid-based isotropic texturing. This paper reports, for the first time, a new single-step Ni-assisted etching technique to obtain nano-scale porous structures, that is, black silicon on multi-crystalline wafers. We observed lower reflection results in comparison with standard isotropic texturing using a standard acid solution. The structural and optical properties of the surface were identified through reflection measurements and scanning electron microscopy imaging. As a final step, the optimized texturing process was applied to multi-crystalline solar cell devices and showed promising results regarding cell performance parameters.


31 August 2022 in Journal of the Turkish Chemical Society Section A: Chemistry
Verified
Journal Article
Open access
PDF file
SKSelcan Karakuş
Selcan Karakuş
CTCihat Tasaltin
Cihat Tasaltin
IGILKE GUROL
ILKE GUROL
BABarbaros Akkurt
Barbaros Akkurt
GBGülsen Baytemi̇r
Gülsen Baytemi̇r
NTNevin Taşaltın
Nevin Taşaltın
Food safety is a crucial issue; all countries have struggled against pesticides for years. In this study, Polypyrrole (PPy)- and Polyacrylonitrile (PAN)-based non-enzymatic electrochemical sensors were investigated to detect the pesticide propamocarb (PM) in food samples. Under the experimental conditions, the proposed strategy exhibited a high selectivity of the disposable PPy-based and PAN-based sensors for the determination of propamocarb pesticide in the concentration of 1 μM with a rapid detection within 1 min at pH 7.4 and 25 °C. We demonstrated the detection of PM residues on cucumber and tomato samples with good electrochemical performances towards the real-time usability on real food samples. PAN-based non-enzymatic electrochemical sensor has good sensitivity, higher selectivity, and stability than PPy-based non-enzymatic electrochemical sensor. The prepared PAN-based non-enzymatic electrochemical sensor is a potential candidate to be used in devices which perform food safety in agricultural products.