The focus of this work is to investigate the effect of emulsifier-free emulsion fuel via steam emulsification (SD) to the diesel engine through physical properties, combustion performance, and exhaust analysis, and compare with conventional emulsion fuel with water percentages of 5% and 10% (E5 and E10) and biodiesel blend (B5). The SD was prepared using a custom 200 mL glass mixing column. The B5 fuel quantitatively was filled in the column, and then the steam was injected from the bottom of the mixing column through the porous frit glass with the pores ranging from 40 to 100 µm. The average water droplet size of SD is 0.375 µm with the average water percentage of 6.18%. The brake specific fuel consumption (BSFC) and brake thermal efficiency (BTE) of SD improved 4.19% and 3.92%, respectively, as compared to B5. The in-cylinder pressure (ICP) was lower than B5, however, yielding close to the B5 at 4 kW engine load. As for the exhaust emission test, NOx and PM for SD were reduced significantly with a percentage reduction of 25.22% and 10.68%, respectively, as compared to neat B5. The steam emulsification method offers a huge potential to be explored further as the concept offers the alternative method of making emulsion fuel without the use of conventional mechanical mixers.
29 August 2021 in Environmental Progress & Sustainable Energy
Bagasse sugarcane (BSC) has low fibre strength due to low cellulose content. Hence, by adding a strong secondary fibre that is high in cellulose such as pineapple leaf fibre (PALF), the fibre strength of the system can be improved. High portion of PALF decreased the composite paper performance because the high composition of PALF tends to produce flocs and agglomerates fibres. The arrangement of the fibres in composite paper should be improved so that this agglomerate’s effect could be overcome. A novel multilayer hybrid fibre composite was used. BSC/PALF with several hybrid ratios was studied in terms of the mechanical and moisture properties of the produced paper sheet and the results showed that multilayer hybrid composite paper produced higher in hybrid composite paper’s properties compared with random hybrid composite paper. The colour of multilayer hybrid fibre composite paper resembled the natural bright colour of BSC and the multilayer hybrid fibre composite paper also shown a slightly low weight loss percentage compared with the random hybrid fibre composite paper after 60 days of soil burial test. As a conclusion, multilayer hybrid fibre composite produced the stronger interfibre bonding and overcome the agglomerate’s effect between BSC/PALF compared with random hybrid fibre composite.
11 February 2022 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
The global focus in emulsion fuels is due to the advantages over conventional diesel fuels. It has the capabilities to simultaneously reduce the emissions of NOx and smoke. It also said to reduce the fuel consumption of diesel engine by significant percentages. However, due to the interdependency on surfactant, emulsion fuel does not seem to be possible as alternative fuel in an economic perspective. This is because of the high market price of the commercial surfactant. Therefore, this research focused on non-surfactant W/D that produced by a system known as Real-Time Non-Surfactant Emulsion Fuel Supply System (RTES). RTES has been applied with the goal of investigating the impact on exhaust emissions and fuel consumption of a mechanical pump fuel injection system diesel vehicle (MP) and a common rail fuel injection system diesel vehicle (CR). A one-ton truck represents as MP (Mechanical Pump) and an SUV represent as CR (Common rail) are the test vehicles for the said research. The non-surfactant W/D with 6.5 wt.% of water produced by the RTES used as the test fuel and named as E6.5. It has been emulsified in the RTES right before being injected into the diesel vehicles. The testing was performed on a chassis dynamometer following the West Virginia University 5-peak cycles. The findings show that the utilization of non-surfactant W/D has increased the fuel consumption by 7.39% for MP and 3.2% for CR respectively as compared with base diesel fuel. NOx, smoke emissions and exhaust temperature have significantly reduced by the MP relative to CR vehicles. Overall, the concept of non-surfactant W/D seems to have implementation potential for reducing harmful emissions from both diesel-powered vehicles.
Palm oil mill secondary effluent (POMSE) is a byproduct of the biological treatment of palm oil mill effluent. This research aims to investigate the mechanism of membrane fouling in the treatment of POMSE using a hybrid membrane photocatalytic reactor (MPR). The effectiveness of MPR in POMSE treatment is currently limited due to membrane fouling on the membrane surface. This study focuses on understanding the various mechanisms of membrane fouling, including complete blocking, intermediate blocking, standard blocking, and cake filtration. The determination of each fouling mechanism is achieved through an analysis of normalized flux data employing the Wiesner and Aptel equation. The results demonstrate a high degree of model fitness (R2 = 0.9576) for MPR Run 3, confirming its effectiveness. Based on the (R2) values and the fitted parameter (Ks^(-1)), it is evident that, under varying pH levels, catalyst types, catalyst loading, and initial POMSE concentrations, the cake formation fouling mechanism prevails in MPR Run. In conclusion, this research holds promising potential for implementation in the wastewater treatment industry while ensuring compliance with environmental regulations.