This study presents the preparation and measurement of a novel environmentally friendly konjac glucomannan (KGM)-based composite aerogels enhanced with wheat straw (WS) via a sol–gel and freeze-drying progress. With the addition of WS, the porosity of aerogels could be increased from 50 to 88.13%, the filtration resistance of aerogels could be reduced from 500 to 205 Pa, and the filtration efficiency could be improved to 90.38%. The addition of WS also enhances the mechanical properties of composite aerogels with compression modulus of 2000.66 Pa, compressive strength of 501.56 Pa and elasticity of 0.603. The results demonstrate the high potential of KGM-based composite aerogels enhanced with WS for applications in air filtering.
Severe acute respiratory syndrome coronavirus (SARS-CoV)-2, the virus that causes the coronavirus disease (COVID)-19, is primarily transmitted through respiratory droplets which linger in enclosed spaces, often exacerbated by HVAC systems. Although research to improve HVAC handling of SARS-CoV-2 is progressing, currently installed HVAC systems cause problems because they recirculate air and use ineffective filters against virus. This paper details the process of developing a novel method of eliminating air pollutants and suspended pathogens in enclosed spaces using Photocatalytic Oxidation (PCO) technology. It has been previously employed to remove organic contaminants and compounds from air streams using the irradiation of titanium dioxide (TiO2) surfaces with ultraviolet (UV) lights causing the disintegration of organic compounds by reactions with oxygen (O) and hydroxyl radicals (OH). The outcome was two functional prototypes that demonstrate the operation of PCO-based air purification principle. These prototypes comprise a novel TiO2 coated fibre mop system, which provide very large surface area for UV irradiation. Four commercially accessible materials were used for the construction of the mop: Tampico, Brass, Coco, and Natural synthetic. Two types of UV lights were used: 365 nm (UVA) and 270 nm (UVC). A series of tests were conducted that proved the prototype's functionality and its efficiency in lowering volatile organic compounds (VOCs) and formaldehyde (HCHO). The results shown that a MopFan with rotary mop constructed with Coco fibres and utilising UVC light achieves the best VOC and HCHO purification performance. Within 2 h, this combination lowered HCHO by 50% and VOCs by 23% approximately.
Photocatalytic oxidation (PCO) is a potential approach for air cleaning, especially when utilizing titanium dioxide (TiO2). A MopFan is similar to a roller brush but is made of flexible fibres coated with TiO2. Unlike conventional filter/mesh UV systems, a MopFan provides a wide UV-TiO2 interaction surface area and airflow passage. This revolutionary technique can be low cost, efficient, and potentially effective against viruses, making it suitable for cleaning indoor air. It is easy to use but technically advanced. The system may be mounted on walls, ffoors, or placed on desktops. A photocatalytic air puriffcation based on MopFan prototype was designed, constructed and tested. This study utilised copper wires (0.1 mm, 0.3 mm, 0.4 mm, and 0.5 mm), plastic fibres (0.5 mm and 1.1 mm), brass wire (0.4 mm), steel wire (0.38 mm), and organic “coco” fibres (0.4 mm). Copper wire (0.5 mm) and organic fibre (0.4 mm) were found to be effective against SARS-CoV-2, but brass (0.4 mm) and plastic (0.5 mm) fibres were found only partially effective. The puriffcation performance was compared using MopFan with plastic (0.5 mm), brass (0.4 mm) and organic “coco” (0.4 mm) fibres but the other materials were rejected due to their poor qualities or difficulties in manufacturing. It was found that the system has a better effectiveness with organic fibres, around 21% of reduction consistently throughout the test. It was also found that by using the photocatalytic MopFan air cleaning system, the final concentration of pollutants in a room is determined by the rate and concentration of pollutant generation.