Yiping Huang

Yiping Huang

Auto-generated profile, based on publicly available information

Yiping Huang

Guangxi Key Laboratory of Manufacturing Systems and Advanced Manufacturing Technology

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2020 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
LLlang hai Liu
lang hai Liu
YHYiping Huang
Yiping Huang
XWXiaoyu Wang
Xiaoyu Wang
RLRuxue Lu
Ruxue Lu
In order to enhance the high‐temperature oxidation resistance properties of Inconel 617 alloy, NiCoCrAlY and NiCoCrAlY CeO2 composite powder coatings metallurgically bonded to substrate were prepared on the surface of Inconel 617 alloy by electron beam cladding. The effect of rare earth oxide CeO2 on the oxidation resistance of NiCoCrAlY coating was investigated. The isothermal oxidation behavior of the substrate and NiCoCrAlY cladding layer with different CeO2 contents (1%, 2%, 3%, and 4%) and without CeO2 oxidized at 1050°C for 20 h, 40 h, 60 h, and 100 h was analyzed. The microstructure and phase composition of the coating after electron beam treatment were tested. The results show that the self‐repair of Al2O3 and Cr2O3 oxide film can be improved under a high‐temperature oxidation environment with the addition of CeO2, and the oxidation resistance of NiCoCrAlY coating can be effectively strengthened by adding CeO2. The improvement effect is most obvious when the content of CeO2 is 2%.

6 October 2016
Verified
Conference Paper
Closed access
XSXiang Sun
Xiang Sun
YHYiping Huang
Yiping Huang
Junke JiangJunke Jiang
Junke Jiang
QLQiuhua Liang
Qiuhua Liang
Ruishen MengRuishen Meng
Ruishen Meng
XCXanping Chen
Xanping Chen
Using first-principles calculation within density functional theory, we study the gas (H2O, H2, H2S, and CO2) adsorption properties of single-layer indium nitride (InN). The four different adsorption sites (Bridge, In, N, Hollow) are chosen to investigate and the most sensitive adsorption site is found (N site for H2 and H2O gases; In site for H2S; center site for CO2) based on the adsorption energy, band gap and charge transfer. Through our research, the results indicate that InN is sensitive to NH3 and H2O. It is shown that H2 gas molecules act as charge acceptors for the monolayer, except H2S, H2O adsorption which are found to be a charge donor. We perform a perpendicular electric field to the system and find its enhancement effect for adsorption energy of gas adsorption. Our theoretical results indicates that monolayer InN is a promising candidate for gas sensing applications.

6 October 2016
Verified
Conference Paper
Closed access
Ruishen MengRuishen Meng
Ruishen Meng
YHYiping Huang
Yiping Huang
QYQun Yang
Qun Yang
XCXianping Chen
Xianping Chen
The gas sensing capability of the graphene-like two dimensional material, antimonene, was investigated by means of first principle calculation to exploit its possibility to be the high performance gas sensor which may benefit from its high surface to volume ratio similar to graphene. The H2, together with the common polluted gases, CO, CH4, H2S and SO2 were selected to examine their affinity with the antimonene monolayer according to the binding energy, charge transfer, adsorption distance and the variation of the bond length and angle. The result shows that the H2 is most chemically inert to antiomnene, followed by the CO and CH4. H2S shows slightly enhanced adsorption strength with adsorption energy of 0.1 eV higher than that of CO and CH4, while the SO2 exhibits the highest reactivity to the antimonene with the the moderate adsorption energy and the apparent charge transfer. More importantly, instead of chemisorption, the physisorption nature of SO2 on antimonene enables the easy desorption by heating and benefit for the recycling use as a gas sensor. In a nutshell, antimonene is a promising candidate as a SO2 gas sensor.

19 August 2019 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
HLHailang Liu
Hailang Liu
YHYiping Huang
Yiping Huang
BWBo Wang
Bo Wang
XWXiaoyu Wang
Xiaoyu Wang
In order to enhance the high-temperature wear resistance of the nickel-base alloy, the electron beam is used to clad the WC-CoCr composite coating on the Inconel 617 surface. A six-factor and three-level orthogonal experiment is designed using Minitab software with scanning beam current, frequency, high voltage, beam spot diameter, offset sweep amplitude, and scanning speed as variables, and the variance and range of the test results are analyzed. The optimal cladding process parameters were determined according to the influence of various factors on the quality characteristics of the cladding layer. The wear behavior at 200°C, 600°C, and 1000°C and microstructure and phase composition of coating before and after electron beam treatment were tested. The results show that the ion exchange between the coating and the substrate is carried out after electron beam treatment. The WC, CoCr, (Fe, Ni)C6, Fe3W3C phase, and solid solution of α-Co were found in the cladding layer, and the microstructure of the coating is mainly dendrite and eutectic on CoCr substrate. The test of wear behavior at high temperature shows that the wear rate of the coating treated by electron beam at 200°C, 600°C, and 1000°C is 10.14 times, 6 times, and 2.29 times lower than that of the substrate, respectively. Moreover, the furrow and scratches of the cladding layer are less than those of the substrate at high temperature. The wear resistance of the coating was improved.