30 March 2022 in Superconductor Science and Technology
SHSimon-Mathieu Bergeron Hartman
Simon-Mathieu Bergeron Hartman
+12
The normal zone propagation velocity (NZPV) of three families of REBCO tape architectures designed for superconducting fault current limiters and to be used in high voltage direct current transmission systems has been measured experimentally in liquid nitrogen at atmospheric pressure. The measured NZPVs span more than three orders of magnitude depending on the tape architectures. Numerical simulations based on finite elements allow us to reproduce the experiments well. The dynamic current transfer length (CTL) extracted from the numerical simulations was found to be the dominating characteristic length determining the NZPV instead of the thermal diffusion length. We therefore propose a simple analytical model, whose key parameters are the dynamic CTL, the heat capacity and the resistive losses in the metallic layers, to calculate the NZPV.
7 June 2021 in IEEE Transactions on Applied Superconductivity
High-temperature superconductors (HTSs) are used in a growing number of applications. Technical HTSs usually consist of superconducting and metallic parts. HTS conductors are characterized by their critical current density and critical temperature defined by the superconducting layer, but other quantities such as the current transfer length (CTL) and the interfacial resistance between the superconducting part and surrounding metals are also important characteristics. Since the CTL and the interfacial resistance cannot be measured directly, a method is known to evaluate these parameters indirectly from the characterization of the spatial variation of the surface voltage of the metallic surrounding that is in direct contact with the superconducting material. In this article, we present the details of the experimental method developed to determine the CTL and the interfacial resistance of commercial second-generation HTS conductors of any type of architecture. We apply this method to quantify the interfacial resistance of ten HTS tapes from six major tape manufacturers. Also, since the architecture of a commercial HTS tape is usually more complicated than an “idealized” superposition of two flat layers (i.e., a metallic layer and a superconducting layer), recourse to three-dimensional numerical modeling has been required in order to understand in details the current transfer mechanisms taking place within the tape. We also show that the method can be applied directly to more complicated structures encountered in HTS cables, namely to determine the barrier resistance between a metallic structure in contact with a superconducting tape, providing important information required in numerical modeling when designing superconducting devices.
25 February 2021 in Superconductor Science and Technology
Copper-stabilized second generation high-temperature superconductor (HTS) coated conductors were modified to enhance their normal zone propagation velocity (NZPV). Experimental results, supported by numerical simulations, indicate that adding copper on the substrate side instead of adding it on the HTS side increases the NZPV by a factor of 2–3. Furthermore, a novel tape architecture, called hybrid-current flow diverter (CFD), was investigated. This hybrid-CFD tape was designed with the goal of having a very long current transfer length, which is the key to enhance the NZPV. Results show that it is possible to fabricate an HTS tape with double stabilizer thickness in comparison to a bare tape, while accelerating the NZPV by a factor of three. With the same approach, a ten-fold increase of the NZPV can be expected for a tape with a 40 µ m thick copper-stabilizer.
12 November 2018 in Superconductor Science and Technology
This paper presents a simple and effective approach to increase the normal zone propagation velocity (NZPV) in (RE)BaCuO thin films grown on a flexible metallic substrate. The concept is an extension of the current-flow-diverter concept already known in the literature. The key idea behind the novel approach is to use a specific geometry of the silver thermal stabilizer that surrounds the superconducting tape. More specifically, a very thin layer of silver stabilizer is deposited on top of the superconductor layer, typically less than 100 nm, while the remaining stabilizer (still silver) is deposited on the substrate side. Normal zone propagation velocities up to 170 cm s −1 at 77 K have been measured experimentally for the first time with this novel architecture, corresponding to a stabilizer thickness of 20 nm on top of the superconductor layer. This is at least one order of magnitude faster than the NZPV speeds measured on commercial 2G HTS tapes. Our results clearly demonstrate that a very thin stabilizer on top of the superconductor layer leads to high normal zone propagation velocities. The experimental values are in good agreement with predictions realized by finite element simulations. Furthermore, the propagation of the normal zone during the quench was recorded in situ and in real time using a high-speed camera. Due to high Joule losses generated on both edges of the tape sample, a ‘U-shaped’ profile could be observed at the boundaries between the superconducting and the normal zones, which matches very closely the profiles predicted by the simulations. The most direct application of this new HTS tape architecture is in high field magnets, since faster quench propagation allows easier detection and protection, which is likely to accelerate substantially the development of HTS magnets used as high-field MRI/NMR systems, etc.
1 March 2021 in Materialia
18 June 2021 in Superconductor Science and Technology
This paper uses both experimental and numerical approaches to revisit the concept of current transfer length (CTL) in second-generation high-temperature superconductor coated conductors with a current flow diverter (CFD) architecture. The CFD architecture has been implemented on eight commercial coated conductor samples from THEVA. In order to measure the 2D current distribution in the silver stabilizer layer of the samples, we first used a custom-made array of 120 voltage taps to measure the surface potential distribution. Then, the so-called ‘static’ CTL ( ) was extracted using a semi-analytical model that fitted well the experimental data. As defined in this paper, the static CTL on a 2D domain is a generalization of the definition commonly used in literature. In addition, we used a 3D finite element model to simulate the normal zone (NZ) propagation in our CFD samples, in order to quantify their ‘dynamic’ CTL ( ), a new concept introduced in this paper and defined as the CTL observed during the propagation of a quenched region. The results show that, for a CFD architecture, is always larger than , whereas when the interfacial resistance between the stabilizer and the superconductor layers is the same everywhere. We proved that the cause of these different behaviors is related to the shape of the NZ, which is curved for the CFD architecture, and rectangular otherwise. Finally, we showed that the normal zone propagation velocity (NZPV) is proportional to , not with , which suggests that the dynamic CTL is the most general definition of the CTL and should always be used when current crowding and non-uniform heat generation occurs around a NZ.