Sheng Li

Sheng Li

Auto-generated profile, based on publicly available information

Sheng Li

Department of Civil and Earth Resources Engineering Kyoto University Kyoto Japan

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 October 2025 in Geophysical Research Letters
Verified
Journal Article
Open access
SLSheng Li
Sheng Li
EFEiichi Fukuyama
Eiichi Fukuyama
Fault slip inevitably causes the multiscale wear damage of asperities, ranging from nanometers to meters. However, the nanoscale asperity wear mechanism remains poorly understood. While plastic wear has been inferred as one of the dominant wear modes, the dynamic wear mechanism of plastic wear has not been thoroughly investigated. Here, we explicitly present a series of nanoscale 3‐D plastic wear processes of α ‐quartz asperities by using molecular dynamics method, where asperity climbing mode dominates during the sliding. We identify a transition from atom‐by‐atom wear damage to layer removal of α ‐quartz asperities with increasing normal forces. Moreover, nanoscale wear volume evolution depends on the normal force and loading velocity and shows sublinear increase with loading distance. We confirm that the tangential shear work can well predict the nanoscale plastic wear volume under various loading conditions due to the proportional relation.

13 November 2025 in Journal of Geophysical Research: Solid Earth
Verified
Journal Article
Open access
SLSheng Li
Sheng Li
EFEiichi Fukuyama
Eiichi Fukuyama
Fault slip commonly leads to the collision and wear failure of asperities across broad length scales. Clarifying the multiscale wear failure mechanisms of asperities is essential for understanding the underlying principle of fault friction behavior. In this study, to investigate the still‐debated wear failure modes of nanoscale asperities, we conduct a series of 3‐D molecular dynamics simulations of semi‐spherical α ‐quartz asperity collisions under different boundary conditions, asperity radii ( R ), and contact configurations. The results indicate that both plastic deformation and fracture of α ‐quartz asperities can occur during frictional collision without creating surface grooves. Under constant normal stiffness‐like condition, the failure transition can be mapped by the vertical overlapping distance normalized by R between the summits of two asperities, as a function of R . Under constant normal load condition, the failure transition can be indicated by the peak tangential shear force. Essentially, the failure mode transition is controlled by subsurface contact stress evolution through the dependence of R and contact configuration. Finally, the results also reveal that the total wear volume of fractured asperities scales linearly with the total tangential shear work. These findings provide deeper insights into the wear failure mechanisms of nanoscale rock asperities during friction, which also help shed light on microscopic fault friction mechanisms.

4 November 2025 in Journal of Geophysical Research: Solid Earth
Verified
Journal Article
Open access
SLSheng Li
Sheng Li
EFEiichi Fukuyama
Eiichi Fukuyama
Nanoscale gouge particles are common products during both rock friction experiments and natural fault slip. However, the frictional wear mechanisms of nanoscale gouge particles and their role in the evolution of fault shear strength remain poorly understood. Therefore, we employed the molecular dynamics method to simulate a series of nanoscale single‐particle wear processes in α ‐quartz sandwiched by two rough surfaces composed of spherical asperities. We explored the effects of asperity interval, particle size, contact configuration and the normal force on the wear damage and wear volume of gouge particles, as well as the influence of particle wear damage mode on the friction coefficient. We observed that higher normal forces could induce particle breakage over shorter loading distances, and the particles underwent three wear stages: stable, sub‐stable, and fracture stages. At stable stage, the wear volume increased linearly with loading distance. Sub‐stable stage was characterized by superliner wear volume growth. The wear volume in both stable and sub‐stable wear stages could be predicted by tangential shear work, as the shear work scaled well with the wear volume. Finally, we measured the critical loading distance until particle fracture. The particle size, normal force and contact configuration could significantly influence the lifetime of α ‐quartz gouge particles, and particle fracture could lead to an immediate increase in friction coefficient rather than a decrease. These findings could provide useful insights into the nanoscale friction and wear mechanisms of gouge particles, which will contribute to the understanding of the microscopic fault frictional behavior.

13 March 2026 in Computers and Geotechnics
Verified
Journal Article
Closed access
XWXin Wei
Xin Wei
PWPengsen Wang
Pengsen Wang
SLSheng Li
Sheng Li

13 October 2026 in Deep Underground Science and Engineering
Verified
Journal Article
Open access
SLSheng Li
Sheng Li
HZHongchang Zhou
Hongchang Zhou
YWYuhao Wu
Yuhao Wu
SWSuifeng Wang
Suifeng Wang
JSJikai Sun
Jikai Sun
Clarifying the fracture mechanisms at the nanoscale is essential for constructing a multiscale framework of rock fracture. In this study, molecular dynamics simulation is employed to investigate the fracture behavior and associated strength evolution in defective α ‐quartz containing either a single hole or double holes under uniaxial compression. The effects of hole size, strain rate, and temperature are analyzed in relation to crack initiation, propagation, and coalescence, and the resulting evolution of uniaxial strength. The results show that the uniaxial strength in all cases is negatively correlated with hole size, while the influence of strain rate is generally limited but varies with hole size. Elevated temperature can reduce both the Young's modulus and peak stress of defective α ‐quartz. Moreover, amorphized zones forming around the lateral edges of holes serve as the primary sites for fracture initiation in all cases, and wing‐like shear fractures represent the dominant propagation mode. The configuration with double holes promotes indirect coalescence in the rock bridge region, while strain rate influences the coalescence patterns depending on hole size. These findings could offer useful insights for developing multiscale models for rock fracture.