Agus Risdiyanto

Agus Risdiyanto

Auto-generated profile, based on publicly available information

Agus Risdiyanto

National Research and Innovation Agency (BRIN)

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2025 in International Journal of Electrical and Computer Engineering (IJECE)
Verified
Journal Article
Open access
PDF file
AKAnt. Ardath Kristi
Ant. Ardath Kristi
ESErwin Susanto
Erwin Susanto
ARAgus Risdiyanto
Agus Risdiyanto
AJAgus Junaedi
Agus Junaedi
RDRudi Darussalam
Rudi Darussalam
AFAhmad Fudholi
Ahmad Fudholi
An active water-cooling system is one of several technologies that has been proven to be able to reduce heat losses and increase electrical energy in photovoltaic (PV) module. This research discusses a comparative experimental study of three pump activation controls in cooling of PV module with the aim of evaluating specifically the PV output power, net energy gain, water flow rate, and module temperature reduction. The three pump activation controls being compared are continuously active during the test, active based on setpoint temperature, and active by controlling the pump voltage using pulse width modulation (PWM) control in adjusting water flow rate smoothly. The results show that controlling the pump voltage using PWM in the PV cooling process produces energy of 437.95 Wh, slightly lower than the others and the average module cooling temperature is 35.24 °C, higher of 1-3 °C than the others. Nevertheless, PWM control of cooling pump has resulted the percentage of net energy gain of 9.94%, greater than other controls, and with an average flow rate of 2.17 L/min, more efficient than the others. Thus, this control is quite effective as it can produce higher net PV energy yield and lower water consumption.

1 August 2023 in International Journal of Electrical and Computer Engineering (IJECE)
Verified
Journal Article
Open access
PDF file
ARAgus Risdiyanto
Agus Risdiyanto
AKAnt. Ardath Kristi
Ant. Ardath Kristi
AJAgus Junaedi
Agus Junaedi
BSBambang Susanto
Bambang Susanto
NRNoviadi A. Rachman
Noviadi A. Rachman
AFAhmad Fudholi
Ahmad Fudholi
In solar power systems, irradiance value data are among the most important parameters. Such data can be used in installing photovoltaic (PV) modules, such as determining the exact location, tilt angle, and required area, for optimal power efficiency. In this study, the comprehensive simulation and implementation of a solar radiation meter with a PV cell and temperature sensor are presented. The irradiance measurement value is based on the power reading generated by the small capacity of the PV cell at a specific load converted into a digital value in the microcontroller using the implicit Newton polynomial interpolation (NPI) equation as a low-cost alternative method. The effect of temperature is included in the conversion to obtain precise measurement results. Firstly, the structure and characteristics of the PV cell are discussed. Secondly, the parameters, measuring method, and conversion of the measurement reading data using the NPI equation are presented to assess the results. Finally, the simulation of the solar radiation meter using the PSIM and implementation of the hardware are conducted to validate the concepts and compare their results. The proposed hardware has an average error of 2.72% in the implementation of the measurement test.

1 November 2018
Verified
Conference Paper
Closed access
KIKristian Ismail
Kristian Ismail
AAAmin Amin
Amin Amin
ARAgus Risdiyanto
Agus Risdiyanto
NRNoviadi Arief Rachman
Noviadi Arief Rachman
Inan electronic circuit, short circuit protection can be done by using passive and active method. The active method is usually using current sensor and/or thermo sensor while the passive method is using trigger design for power circuit such dead time delay trigger or digitally interlock trigger for high side and low side. Dead time delay method can increase the total harmonic distortion (THD) while the interlock method must add more components. This paper discusses the design of Gray code for passive short circuit protection. Gray code is widely used in the field of communications technology, mechanical engineering, and digital data processing because the Gray code can minimize errors. The Gray code converts an integer value, represented as a voltage, into a series of pulses in digital form. In inverter design based on microcontroller, calculations to generate AC modulation is done in the microcontroller. This increases programming complexity and amount of coding downloaded to the microcontroller chip while the capacity of the flash memory in the microcontroller is limited. In turn, this makes program execution time is longer. This paper discusses the design of a single phase inverter using unipolar method with modulation of the sine wave and the triangular wave is done outside the microcontroller using data processing software application (Microsoft Excel) and short circuit protection using gray code modulation.

1 October 2025 in International Journal of Electrical and Computer Engineering (IJECE)
Verified
Journal Article
Open access
PDF file
RDRudi Darussalam
Rudi Darussalam
ARAgus Risdiyanto
Agus Risdiyanto
AKAnt Ardath Kristi
Ant Ardath Kristi
AJAgus Junaedi
Agus Junaedi
NRNoviadi Arief Rachman
Noviadi Arief Rachman
AFAhmad Fudholi
Ahmad Fudholi
This study experimentally investigates the performance of bifacial photovoltaic (bPV) modules under vertical and tilted orientations in a tropical region. Related studies are reviewed, then performance metrics including solar radiation, module temperature, bifaciality gain, and energy yield were monitored and analyzed over a specified period. The aim is to determine the optimal orientation for maximizing output power generation, temperature module, and understanding the bifaciality factor through real-world conditions. The experimental setup consisted of three different bifacial photovoltaic module configurations: two vertically mounted with facing east-west (E/W) and north-south (N/S) respectively, while the third was tilted 15 facing north. The study findings revealed that the tilted orientation produced the highest energy yield of 1951 Wh, followed by the vertical east-west (E/W) and vertical north-south (N/S) orientations with 1504 Wh and 609 Wh, respectively. While tilted bPV module benefit from higher irradiance, they also experience elevated temperatures (39% above ambient) compared to vertically bPV modules (8-21%). This can negatively affect efficiency, especially during peak solar hours. The results also show that differences in bPV installation orientation affect the bifaciality factor and gain. These findings offer valuable guidance for optimizing bPV system design and deployment in tropical regions with low latitude, supporting sustainable energy solutions.