1 April 2015 in International Journal of Advanced Robotic Systems
The introduction of robotic surgery within the operating rooms has significantly improved the quality of many surgical procedures. Recently, the research on medical robotic systems focused on increasing the level of autonomy in order to give them the possibility to carry out simple surgical actions autonomously. This paper reports on the development of technologies for introducing automation within the surgical workflow. The results have been obtained during the ongoing FP7 European funded project Intelligent Surgical Robotics (I-SUR). The main goal of the project is to demonstrate that autonomous robotic surgical systems can carry out simple surgical tasks effectively and without major intervention by surgeons. To fulfil this goal, we have developed innovative solutions (both in terms of technologies and algorithms) for the following aspects: fabrication of soft organ models starting from CT images, surgical planning and execution of movement of robot arms in contact with a deformable environment, designing a surgical interface minimizing the cognitive load of the surgeon supervising the actions, intra-operative sensing and reasoning to detect normal transitions and unexpected events. All these technologies have been integrated using a component-based software architecture to control a novel robot designed to perform the surgical actions under study. In this work we provide an overview of our system and report on preliminary results of the automatic execution of needle insertion for the cryoablation of kidney tumours.
1 April 2013 in European Journal of Radiology
22 January 2024 in IEEE Sensors Journal
Monitoring and assessment of coastal and river velocities plays a key role in both scientific and industry applications. Field measurements are key for decision making for resource management and protection, as well as for validation of numerical models and climate change studies. In this paper, a Hall effect sensor-based cost effective novel device is proposed for measuring velocities and direction of near-bed currents, and water-level. This device, called the Hydromast, provides instantaneous measurements in real-world conditions, and is equipped with communication capabilities to allow near real-time data transfer and monitoring. The validation of the device is performed in real-world steady and unsteady flow conditions. Within the device measurement range it is shown that the root-mean-square-error of the time averaged flow measurements is under 0.1m/s.
28 July 2022 in IEEE Robotics and Automation Letters
In this research we show a characterization of mud behavior under vertical stepping. We showed that mud stiffness can vary 45-fold and the energy spent to generate equivalent impulse can vary 2-fold depending on the mud water content, but also that stepping faster on mud leads to lower peak forces and higher energy consumption. Next, we showed that the peak force generated can be increased by 33% by changing the foot stiffness, but is reduced by 18% if stepping is repeated on the same spot. We then demonstrated how force control can be used to achieve identical force profiles on very different muds. These results will help to design mechanical parts or control strategies for legged robot locomotion on mud.
1 June 2014 in Acta Radiologica Short Reports
Trends in interventional radiology and urology training are orientated towards reducing costs and increasing efficiency. In order to comply with the trends, we propose training on inexpensive patient-specific kidney phantoms. To develop a new kidney phantom for puncture and drainage training in interventional urology and radiology, and to evaluate their anatomical correctness and suitability for training compared to the traditional way of training on home-made phantoms. A case study for validation of kidney phantoms was conducted with nine radiology students divided into two groups: one trained on standard home-made training phantom (n = 4) and the other on our kidney phantoms (n = 5). Another test phantom was used to evaluate the effectiveness of the training of the two groups. The tests were video recorded and analyzed. Duration of the procedure was used as the primary indicator of procedure’s quality. Comparison tests were also conducted with professional radiologists. Anatomical correctness of the kidney phantom was evaluated by comparing the post mortem kidney scans with reconstructed models from CT scans. Subjective feedback was also collected from the participants. Wider use of kidney phantoms was analyzed. The average volumetric difference between post mortem kidney scans and reconstructed CT kidney models was 4.70 ± 3.25%. All five students practicing on the kidney phantom improved their performance and the results were almost equal to the results of the professional radiologist while in the other group two students out of four trained on standard home-made training phantoms failed to improve their performance. However, the small number of test subjects prevents us from drawing general conclusions about the efficiency of the new practice. The kidney phantoms were found usable also for nephrostomy catheter placement training under fluoroscopy. The feedback from radiologists showed that the anatomically correct features of the phantom is an added value for the training and has a potential to increase the quality of minimally invasive procedures in general.
28 August 2019 in IEEE Sensors Journal
The near-bed velocity is a key physical parameter in hydrological, ecological and geomorphological studies. Considering climate change, measurement methods capable of providing continuous observations are needed to assess and predict the effects of increasing uncertainty. Therefore, a technology gap remains for continuous near-bed measurements. To address this gap, we have developed a multimodal flow measurement device, the hydromast. The hydromast uses a combination of pressure and inertial sensing to measure the nearbed (< 30 cm) velocity. We have previously shown that the device can be used to classify river hydromorphological units. Encouraged by these results, we now show that the same device is also capable of continuously measuring the near-bed velocity in rivers. Ten hydromast prototypes were built and calibrated over the range of 0.01 – 2 m/s in a large-scale laboratory tow tank and validated under natural conditions (0.35 – 1.2 m/s) using 118 turbulent flow measurements in a river. It was found that the streamwise, time-averaged velocity mean estimation error from the hydromast in continuous tests with different methods was 0.095 m/s, as compared with a state-of-the-art acoustic Doppler velocimeter. The contribution of this study is a new method for continuous near-bed velocity measurements, verified with turbulent field data from a river.