8 November 2023 in Advances in Structural Engineering
Rib-to-deck (RTD) innovative double-sided welded joints have the potential to enhance the fatigue resistance of orthotropic steel decks (OSDs). However, welding residual stress (WRS) has been reported to be a contributing factor to fatigue cracking of steel bridges. This paper performed fatigue crack growth of the RTD innovative double-sided welded joints of OSD considering WRS. Firstly, a thermal-mechanical sequential coupling finite element model (FEM) of the RTD double-sided welded joints was established. The WRS distribution along the direction of deck thickness was analyzed. Secondly, the FEM of the OSD segment with crack was established. The fatigue crack behavior of RTD double-sided welded joints under the combined action of vehicle load and WRS was studied. Finally, the influences of initial crack on fatigue life was analyzed. Results indicate the distribution of the transverse WRS along the direction of deck thickness is tension-compression-tension stress, which has the characteristics of the sinusoidal function. The ∆ K eff value increases significantly considering WRS than without considering WRS during crack growth. WRS has a significant effect on fatigue life, and the fatigue life of the weld toe without considering WRS is about twice that of considering WRS. The crack depth and aspect ratio ( a 0 / c 0 ) of the initial crack affect the fatigue life of RTD double-sided welded joints.
19 May 2021 in Advances in Structural Engineering
Fatigue damage accumulation is a critical factor resulting in the failure of prestressed concrete (PC) bridges. The fatigue damage is usually caused by the coupled effect of cyclic vehicle loading and environmental corrosion. This study investigated probabilistic fatigue damage on aging PC bridges considering both stochastic traffic loading and corrosion. A stochastic traffic model was derived based on long-term monitoring data aiming to simulate fatigue stress spectra of critical rebar. The effect of cracks on the fatigue stress spectra was investigated in order to model the fatigue stress state more realistically. A three-stage traffic growth model was established based on traffic volume histories of three highways in China. A fatigue limit state function considering traffic growth and corrosion effect was deduced for fatigue reliability assessment of PC bridges. Numerical results show that the stress amplitude of rebar considering cracks is 1.53 times greater than the rebar with no-cracks, resulting in a decrease of fatigue life by 68 years. In addition, the three-stage traffic growth models lead to 25 years shorter fatigue life than the one considering a linear traffic growth model. Finally, the corrosion effect results in a fatigue life of 44 years. The numerical results provide a theoretical basis for fatigue life estimation and maintenance of aging PC bridges.
21 October 2024 in Engineering Failure Analysis
10 May 2024 in Journal of Building Engineering
1 January 2025 in Structural Control and Health Monitoring
With the development of computer and image processing technologies, computer vision (CV) has been attracting increasing attention in the field of civil engineering measurement and monitoring. Cables in slender structures have unique challenges for CV‐based vibration measurement methods, such as low pixel proportion and sensitivity to environmental conditions. This study proposes a noncontact vibration measurement method based on a line tracking algorithm (LTA). The robustness and applicability of the proposed method under varying image resolutions, signal‐to‐noise ratios, and cable inclination angles were systematically evaluated through experimental test of a cable specimen. To validate the effectiveness of the proposed method for practical detection applications, a vibration test on a scaled cable‐stayed bridge model was carried out. The numerical result indicates that the LTA provides high reliability and accuracy values of the cable force. The maximum errors of the first‐order self‐vibration frequency and cable force of the scaled cable‐stayed bridge is 0.99% and 2%, respectively. The proposed method maintains strong stability across various conditions, which provides a reference for long‐term structural health monitoring of cable‐stayed bridges.
1 January 2025 in Structural Control and Health Monitoring
Engineering structures usually have rare damage scenarios, which provide insufficient labels to identify the structural damage. Therefore, the effectiveness and accuracy of traditional data‐driven methods with limited training samples is an urgent task. This study develops a semisupervised transfer learning (TL) method for structural damage identification. The effectiveness is validated through experiments on a scale cable‐stayed bridge specimen. Initially, a convolutional neural network (CNN) was trained based on a numerical dataset simulated by a finite element model, where a source domain is modeled with strong recognition performance and generalizability. Subsequently, the network structure and hyperparameters in the source domain were transferred to the corresponding positions in the experimental training model to create a pretrained model in the target domain; this pretrained model was updated by using site‐specific measured data from the engineering structure in the target domain. Finally, a dynamic threshold self‐training algorithm was employed to further optimize the model: in the initial stage, a high‐confidence threshold of 90% was set to filter reliable pseudolabels, and the threshold decreases to 80% gradually, under the condition that the model cannot provide predictions with sufficiently high confidence. Experimental study on a scale cable‐stayed bridge specimen was conducted to demonstrate the effectiveness of the proposed method. Four networks were established based on (1) experimental samples; (2) both labeled and unlabeled experimental samples with the self‐training algorithm; (3) TL from the finite element model and experimental samples; and (4) applying self‐training with unlabeled samples to the target model derived from TL. The results indicate that the damage identification accuracy of the aforementioned models is 73.6%, 79.4%, 84.6%, and 89.8%, respectively. The TL improves the reliability of generating pseudolabels by utilizing the self‐training process and unlabeled data and decreases errors in pseudolabels. Both finite element simulation data and practical unlabeled sample data were successfully combined by the TL and self‐training semisupervised learning method for damage identification in cable‐stayed bridges effectively.