1 February 2018 in Journal of Applied Physics
We performed a series of systematic spall experiments on single-crystal copper in an effort to determine and isolate the effects of crystal orientation, peak stress, and unloading strain rate on the tensile spall strength. Strain rates ranging from 0.62 to 2.2 × 106 s−1 and peak shock stresses in the 5–14 GPa range, with one additional experiment near 50 GPa, were explored as part of this work. Gun-driven impactors, called flyer plates, generated flat top shocks followed by spall. This work highlights the effect of crystal anisotropy on the spall strength by showing that the spall strength decreases in the following order: [100], [110], and [111]. Over the range of stresses and strain rates explored, the spall strength of [100] copper depends strongly on both the strain rate and shock stress. Except at the very highest shock stress, the results for the [100] orientation show linear relationships between the spall strength and both the applied compressive stress and the strain rate. In addition, hydrodynamic computer code simulations of the spall experiments were performed to calculate the relationship between the strain rate near the spall plane in the target and the rate of free surface velocity release during the pullback. As expected, strain rates at the spall plane are much higher than the strain rates estimated from the free surface velocity release rate. We have begun soft recovery experiments and molecular dynamics calculations to understand the unusual recompression observed in the spall signature for [100] crystals.
22 August 2018 in Journal of Applied Physics
Materials subjected to dynamic environments experience a complex and wide range of stress, strain, and strain-rate conditions. To have confidence in material models, an accurate, predictive capability is required. In this study, we present a series of flyer-plate impact tests on well characterized, high purity tantalum. The shock-waves generated at impact release from the free-surfaces, reflect, and interact to produce incipient spall fracture. By varying the flyer-plate material and impact velocity, both the peak stress and the strain-rate in the samples were controlled independently. Velocimetry was used on the rear free-surface of the samples to measure the shock-response and the spall strength. While this measurement provided the same spall strength for all cases, at approximately 5.1 GPa, when the samples were sectioned during post-mortem, the quantity and distribution of internal damage was markedly different. For the high-strain rate cases, voids remained small and isolated, whereas in the lower strain-rate experiments, the spall damage was far more localized, with a well-defined continuous spall plane. With the use of hydrocode simulations, this was discovered to result from how the different release rates affect the interaction volume inside the sample. These results highlight the importance of careful sample recovery, and the risks of relying solely on free-surface velocity measurements.
10 December 2018 in Journal of Applied Physics
We present a series of experiments on the response of additive manufactured (AM) tantalum to dynamic loading, specifically the spall strength. Rectangular plates of AM tantalum were produced, with subsequent characterization revealing a highly anisotropic microstructure. Samples were taken from these plates to investigate the effect of anisotropy on the spall strength: the resistance to high strain-rate tensile damage. A conventional, wrought tantalum sample, possessing an equiaxed microstructure, was also tested to serve as a control. Shock loading was performed via light gas-gun flyer-plate impact experiments, with laser velocimetry on the rear of the samples to record the shock wave profiles and soft-recovery techniques to allow post-mortem analysis. In general, the AM samples were found to have a higher Hugoniot elastic limit, the dynamic yield strength under shock loading, while having a reduced spall strength, when compared to the wrought tantalum samples.
6 November 2019 in Physical Review E
Recently, Richtmyer-Meshkov instability (RMI) experiments driven by high explosives and fielded with perturbations on a free surface have been used to study strength at extreme strain rates and near zero pressure. The RMI experiments reported here used impact loading, which is experimentally simpler, more accurate to analyze, and which also allows the exploration of a wider range of conditions. Three experiments were performed on tantalum at shock stresses from 20 to 34 GPa, with six different perturbation sizes at each shock level, making this the most comprehensive set of strength-focused RMI experiments reported to date on any material. The resulting estimated average strengths of 1200–1400 MPa at strain rates of exceeded, by 40% or more, a common power law extrapolation from data at strain rates below . Taken together with other data in the literature that show much higher strength at simultaneous high rates and high pressure, these RMI data isolated effects and indicated that, in the range of conditions examined, the pressure effects are more significant than rate effects.
22 June 2020 in Journal of Applied Physics
Spall fracture is a high strain-rate damage phenomenon associated with shock or impulsive loading events. When a material that has been subjected to shock compression is allowed to release, rarefaction waves propagate into the sample and reduce the internal stress to zero. If multiple rarefaction waves intersect, they generate tension which, if sufficient, can nucleate voids in the material. It has been observed in several works investigating spall fracture that although the shock-wave profiles suggested spall occurred, imaging of the recovered sample revealed no voids or cracks. In this study, we aim to determine whether a second shock event could recompact existing spall damage, and if so, what form does the microstructure at the recompaction interface have? Through a series of gas-gun flyer-plate impact experiments, we demonstrate that modest shock stresses of 2 GPa–3 GPa are enough to both fully compact a damaged copper target back to a state of zero porosity and, furthermore, drive recrystallization of the interface such that there is a new bond formed where the free surfaces were brought together.
28 July 2020 in Journal of Applied Physics
Research was undertaken to study spall and subsequent recompaction of oxygen-free high-thermal-conductivity copper using a single-stage large-bore light gas gun capable of planar impacts. Gun experiments were conducted that produced an initial spall in the target with a subsequent recompaction of the spall damage/layer by the use of layered impactors. Symmetric spall experiments at similar conditions were also conducted as a control to the recompaction experiments. Photonic Doppler velocimetry was used to obtain the velocity history of the target's back surface; these velocity histories were analyzed, and the results were compared to numerical simulations. After recovery of selected samples, the microstructure was analyzed using optical imaging microscopy and electron backscatter diffraction. Recompaction waves were clearly observed in the time-resolved data obtained at the back surface of the targets. Two different series of experiments were performed to understand the effect of damage morphology on the stress required for spall recompaction. In the initial series, the peak pressure of the first shock was systematically increased to alter the amount of damage in the material. While in the second series, the peak pressure of the second shock was increased, keeping the magnitude of the first shock relatively constant to understand the effect of peak stress on the recompaction process. Findings clearly show that recompaction results in a perturbed band of the microstructure at the location of the expected spall plane in all cases except where the peak stress of the second shock is lower than the critical value.