1 February 2010 in Géotechnique
The driven monopile is currently the preferred foundation type for most offshore wind farms. While the static capacity of the monopile is important, a safe design must also address issues of accumulated rotation and changes in stiffness after long-term cyclic loading. Design guidance on this issue is limited. To address this, a series of laboratory tests were conducted where a stiff pile in drained sand was subjected to between 8000 and 60 000 cycles of combined moment and horizontal loading. A typical design for an offshore wind turbine monopile was used as a basis for the study, to ensure that pile dimensions and loading ranges were realistic. A complete non-dimensional framework for stiff piles in sand is presented, and applied to interpret the test results. The accumulated rotation was found to be dependent on relative density, and was strongly affected by the characteristics of the applied cyclic load. Particular loading characteristics were found to cause a significant increase in the accumulated rotation. The pile stiffness increased with number of cycles, which contrasts with the current methodology where static load–displacement curves are degraded to account for cyclic loading. Methods are presented to predict the change in stiffness and the accumulated rotation of a stiff pile due to long-term cyclic loading. The use of the methods developed is demonstrated for a typical full-scale monopile.
1 January 1982 in Chemical Engineering Science
1 June 2006 in Geotechnical and Geological Engineering
1 January 2013 in Journal of Geotechnical and Geoenvironmental Engineering
Skirted gravity base foundations and suction caisson foundations are considered as viable alternatives to monopile foundations for offshore wind turbines. While recent work has focused on the monotonic moment-rotation response for shallow foundations, the cyclic response and the accumulation of rotation over the life of the turbine must also be addressed. This paper presents cyclic loading tests where approximately 10,000 cycles, with different loading characteristics, were applied to a model shallow foundation (a caisson) in loose sand. On the basis of these tests, a framework for assessing the accumulated angular rotation because of cycling was developed. The settlement and cyclic stiffness response of the caisson were also assessed. It was found, not unexpectedly, that the accumulated settlement of the caisson increased with the number of cycles and cyclic amplitude. It was also found that a cyclic loading regime intermediate between one-way and full two-way cycling produced the largest rotations. The cyclic stiffness was relatively unaffected by the number of cycles. Using an appropriate scaling technique, the proposed framework was used to predict the long-term accumulated angular rotation, for an example, the field-scale monocaisson structure.
1 February 2015 in Engineering Geology
This paper presents a numerical investigation of the behaviour of dry granular flows generated by the collapse of prismatic columns via 3D Distinct Element Method (DEM) simulations in plane strain conditions. Firstly, by means of dimensional analysis, the governing parameters of the problem are identified, and variables are clustered into dimensionless independent and dependent groups.Secondly, the results of the DEM simulations are illustrated. Different regimes of granular motion were observed depending on the initial column aspect ratio. The profiles observed at different times for columns of various aspect ratios show to be in good agreement with available experimental results.Thirdly, a detailed analysis of the way energy is dissipated by the granular flows was performed. It emerges that most of the energy of the columns is dissipated by inter-particle friction, with frictional dissipation increasing with the column aspect ratio. Also, the translational and rotational components of the kinetic energy of the flows, associated to particle rotational and translational motions respectively, were monitored during the run-out process. It is found that the rotational component is negligible in comparison with the translational one; hence in order to calculate the destructive power of a granular flow slide, only the translational contribution of the kinetic energy is relevant.Finally, a methodology is presented to calculate the flux of kinetic energy over time carried by the granular flow through any vertical section of interest. This can be related to the energy released by landslide induced granular flows impacting against engineering structures under the simplifying assumption of neglecting all structure-flow interactions. This represents the first step towards achieving a computational tool quantitatively predicting the destructive power of a given flow at any location of interest along its path. This can be useful for the design of engineering works for natural hazard mitigation. To this end, also the distribution of the linear momentum of the flow over depth was calculated. It emerges that the distribution is initially bilinear, due to the presence of an uppermost layer of particles in an agitated loose state, but after some time becomes linear.This type of analysis showcases the potential of the Distinct Element Method to investigate the phenomenology of dry granular flows and to gather unique information currently unachievable by experimentation
1 November 2006 in Géotechnique
Laboratory tests applying vertical and moment loads to suction caissons founded in sand and clay have been conducted to simulate an equivalent series of field tests. The caissons used in the laboratory were 0·15 m, 0·2 m and 0·3 m in diameter, whereas those for the field tests were 1·5 m and 3·0 m in diameter. The loads applied to the caissons in the laboratory tests were scaled from those in the field tests, and the models were loaded in a near-identical manner to the field trials. The test results are presented in non-dimensional form for comparison. The non-dimensional laboratory data from moment loading tests were similar to the field data in most cases. However, the non-dimensional data from vertically loaded caisson tests in the laboratory and in the field show more significant differences, and possible reasons for these are discussed.