In this work, magnesium oxide nanoparticles were synthesized by the sol-gel route and their ecotoxicity was tested in worms of the Eisenia andrei species. Magnesium oxide nanoparticles were characterized by XRD, surface area via BET, TEM and SEM-FEG/EDS. The lethality test with Eisenia andrei earthworm species followed the recommendations of ISO 11268-1 (ISO, 2012) in a completely randomized design with six replicates for each concentration tested (1.06, 2.12, 4.24, 8.48 and 16.96 μg of NPs-MgO/kg of soil), plus the control. The concentrations were mixed to the tropical natural soils, Entisol Typic Quartzipsamments and Oxisol, with no agricultural use history. The morphological and structural analyses of the nanoparticles indicated the formation of magnesium oxide with cubic structure, constituting agglomerates of nanostructures of the order of 20 to 50 nm. The results of toxicity were submitted to analysis of variance (ANOVA One-way), followed by the Dunnett test (p <0.05). Based on standardized toxicological tests it was found that NPs-MgO, at the concentrations tested, did not affect the survival of Eisenia andrei species in the natural soils studied.
Composites based on green high-density polyethylene (G-HDPE) and hydroxyapatite (HA) compatibilized with maleic anhydride grafted high-density polyethylene (HDPE-g-MAH) were developed in this work. The main objective was to evaluate the effects of HA and HDPE-g-MAH contents on the mechanical and thermal properties and hydrolytic degradation of composites through design of experiments and statistical analysis, as well as to evaluate the hemolytic stability. Hydroxyapatite acts as a reinforcing agent for the G-HDPE matrix while the HDPE-g-MAH acts as a compatibilizing agent, improving the dispersion of the HA particles in the polymer matrix and thus increasing the mechanical properties. The crystallization temperature and the degree of crystallinity of the polymer matrix were increased with the addition of HA, suggesting the filler acts as a heterogeneous nucleating agent. Hemolysis tests performed on a composite sample with best mechanical performance did not indicate significant hydrolytic degradation, which suggests this composite is a promising material to be used in bone tissue engineering, for application in implants and bone grafts.
This work describes the second of a series of studies of the effects of injection molding conditions on the mechanical and thermal properties of Polyamide 6/Glass Fiber/Montmorillonite (PA6/GF/MMT) composites and was motivated by the lack of information about how the processing variables influence on the properties of three-phase composites containing fiber glass. By this time, the effects of the injection molding temperature associated with the fiber glass percentage on the mechanical and thermal properties of the composite are investigated. Some samples were processed, following a statistical experimental factorial planning, varying the mold temperature and the fiber glass percentage and maintaining 5 wt % of the MMT. The samples were submitted to tensile and flexural tests, XRD, SEM and DSC. The studies showed that an increase in the mold temperature and the fiber percentage improves the maximum tensile and flexural stresses. The increased mold temperature slows the cooling rate, which, over time, decreases the degree of crystallinity. However, there is an increase in the intercalation of the polymeric chains and the nanoclay lamellae, and the structure forms with fewer defects.
4 February 2021 in Brazilian Journal of Environmental Sciences
The generation of large amounts of ash from sugarcane bagasse by its producing countries is becoming a worldwide-problem. Its irregular application, such as in fertilizers, contaminates soil and water, causing a great environmental problem. Studies show it is possible to apply ash in some specific areas, such as replacement of portland cement, replacement of clay, as an adsorbent, in the treatment and stabilization of soils, in the pavement of road asphalt, among others. The objective of the present article is to evaluate which are the most promising areas for the use of sugarcane bagasse ash. The work was developed with a bibliographic search, using the bibliometrics technique. The results obtained show that it is possible to use ash in several different areas. However, having a detailed study of the characteristics of the ash obtained is important, because they are directly related to the regions and climates where sugarcane is cultivated, besides its granulometry, collection time the ashes in the boilers, pHs, curing time, etc. In conclusion, results can be very different for the same application area, depending on the properties of the ash obtained.
The electroactive polymers have been the subject of many studies in the last decade, mainly because its unique properties. They are used in composite structures, which allow its application in many fields, as for example, sensors and artificial muscles. The electrical properties of these composites are influenced by the doping state of the electroactive polymer, which is controlled during its synthesis process. Therefore, this work aimed to evaluate how the synthesis parameters influence the electrical conductivity of the composite PANI/PVDF. The synthesis parameters evaluated were the concentrations of monomer, initiator and dopant, and the synthesis time. PANI was obtained by chemical polymerization in a solution containing PVDF and the solvent DMF. To evaluate possible changes in the chemical structure of the composite, the samples were submitted to FT-IR and XRD analysis. It was possible to conclude that the parameters relative to the production of PANI directly influence in the electrical conductivity of the composite. So, the sample produced with major quantities of monomer, initiator and dopant were statistically significant to increase the electrical property of the composite.