Bahman Taherkhani

Bahman Taherkhani

Auto-generated profile, based on publicly available information

Bahman Taherkhani

SDU Soft Robotics Biorobotics Section The Maersk McKinney Moller Institute University of Southern Denmark Odense Denmark

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 August 2020 in Journal of Elastomers & Plastics
Verified
Journal Article
Closed access
PDF file
BTBahman Taherkhani
Bahman Taherkhani
AAAli Pourkamali Anaraki
Ali Pourkamali Anaraki
JKJavad Kadkhodapour
Javad Kadkhodapour
SRSaeed Rezaei
Saeed Rezaei
HTHaoyun Tu
Haoyun Tu
Auxetic materials are a family of rationally designed artificial structures that have unique effective properties gained from the distribution of the internal architecture rather than of the chemical composition. This article used the modified solid isotropic material with penalization method for topology optimization of 2D re-entrant auxetic structures with different Poisson’s ratios and volume fractions. The obtained structures were verified by the finite-element method (FEM) using the commercial FEM software and also validated by the experimental approach. A good agreement was achieved between the experimental and numerical results. Then, the cell geometry effect on Poisson’s ratio under large tension was investigated. Our study revealed that the location and stiffness of rotation joints are two new parameters affecting Poisson’s ratio value. Poisson’s ratio will decrease by decreasing the stiffness of rotation joints and positioning the rotation joints closer to the middle of the structure. So, from the investigation of the optimizer performance, it was achieved that re-entrant auxetic structures with different Poisson’s ratios could be easily designed by changing just the location of rotation joints. This will be applicable in many applications like sensor field.

25 June 2025 in Advanced Robotics Research
Verified
Journal Article
Open access
BSBurcu Seyidoğlu
Burcu Seyidoğlu
APAida Parvaresh
Aida Parvaresh
BTBahman Taherkhani
Bahman Taherkhani
ARAhmad Rafsanjani
Ahmad Rafsanjani
Kirigami offers unique opportunities for guided morphing by leveraging the geometry of the cuts. This work presents inflatable kirigami crawlers created by introducing cut patterns into heat‐sealable textiles to achieve locomotion upon cyclic pneumatic actuation. Inflating traditional air pouches results in symmetric bulging and contraction. In inflated kirigami actuators, the accumulated compressive forces uniformly break the symmetry, enhance contraction compared to simple air pouches by two folds, and trigger local rotation of the sealed edges that overlap and self‐assemble into an architected surface with emerging scale‐like features. As a result, the inflatable kirigami actuators exhibit a uniform, controlled contraction with asymmetric localized out‐of‐plane deformations. This process allows us to harness the geometric and material nonlinearities to imbue inflatable textile‐based kirigami actuators with predictable locomotive functionalities. We thoroughly characterized the programmed deformations of these actuators and their impact on friction. We found that the kirigami actuators exhibit directional anisotropic friction properties when inflated, having higher friction coefficients against the direction of the movement, enabling them to move across surfaces with varying roughness. We further enhanced the functionality of inflatable kirigami actuators by introducing multiple channels and segments to create functional soft robotic prototypes with versatile locomotion capabilities.

2 June 2024 in Advanced Engineering Materials
Verified
Journal Article
Open access
BTBahman Taherkhani
Bahman Taherkhani
MÇMehmet Fatih Çelebi
Mehmet Fatih Çelebi
MÇMünire Sibel Çetin
Münire Sibel Çetin
AAAsli Tuncay Atalay
Asli Tuncay Atalay
GIGökhan Ince
Gökhan Ince
OAOzgur Atalay
Ozgur Atalay
Soft grippers, generating movement immediately, are generally based on flexible materials actuated by air pressure and comprised of bulky parts, including valves, compressors/pumps, motors, and tubes. In this work, a compact soft gripper with the ability to actuate with a low boiling point liquid (acetone) is presented. SolidWorks 2021 software and 3D printing technology are used to design and manufacture the gripper molds, respectively. The constitutive material of the soft gripper body is highly flexible Ecoflex. A silver‐coated nylon fabric (SCNF) heater reinforced with stainless steel yarn (SSY) covering the external surface of the gripper is designed and manufactured using Autocad 2021 and a laser cutting machine, respectively. The idea is inspired by floating the gripper in warm water to provide smooth heat over a large surface area. The available commercial software Abaqus2021 is used to simulate the mechanical deformation of the gripper, and its results are verified with experimental results. The parameter's effect including the voltage and low boiling liquid volume on achievable force and actuating time are investigated. The relation between the electrical, thermal, and mechanical properties of the presented gripper is discussed in detail.

15 December 2023 in Journal of Materials Science
Verified
Journal Article
Closed access
PDF file
BTBahman Taherkhani
Bahman Taherkhani
RNRoohallah Nasri
Roohallah Nasri
AAAsli Tuncay Atalay
Asli Tuncay Atalay
MCMotaleb Malmir Chegini
Motaleb Malmir Chegini
OAOzgur Atalay
Ozgur Atalay

8 May 2023 in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Verified
Journal Article
Closed access
BTBahman Taherkhani
Bahman Taherkhani
SRSahar Rahmani
Sahar Rahmani
OAOzgur Atalay
Ozgur Atalay
Auxetic materials have different types whose mechanical behaviors are different from each other, and these differences affect their sensitivity. However, in the piezo-resistive strain sensor field, less attention has been paid to this variety of structures. In this article, the isotropic auxetic structure with three axes of symmetry was used to construct the isotropic linear piezo-resistive strain sensor. Structures that have only three or six symmetry axes have isotropic mechanical behavior, and structures with many symmetry axes other than these two cases are not isotropic. Also, to obtain a sensor with a linear sensing performance, the Poisson's ratio of the sensor must be constant during the strain. Most of the structures presented in the previous works have a variable Poisson's ratio along the strain. When the Poisson’s ratio of the structure is constant during the strain, it causes the sensing elements to have the same increased space to separate from each other during the strain, and as a result, the sensor will have a linear performance. A computer numerical control device was utilized to manufacture the sensor mold. Silicon RTV2 as a substrate material, and graphite powder as a sensing element were mixed to provide the sensor constitutive material, and molded into the manufactured die. To evaluate the response of the sensor in different directions, the sensitivity tests were performed in the directions of 0°, 60°, and 120°, which are compatible with each other, and also the suggested sensor has linear sensitivity during the strain.

13 April 2024 in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Verified
Journal Article
Closed access
BTBahman Taherkhani
Bahman Taherkhani
AAAsli Tuncay Atalay
Asli Tuncay Atalay
OAOzgur Atalay
Ozgur Atalay
The (comparative) study on the multidirectional piezo-resistive scenario of conventional and auxetic sensors is presented using silicone RTV2 as a base material coated with graphite powder as a sensing element. The key parameter of this comparison is the added area that appeared by applying the strain. The larger this parameter is, the larger the area for the sensing elements separation, and subsequently, the greater the sensitivity. To do the sensing performance test in a three-directional mode, a low-cost idea is to use a chuck lathe and an electric motor to open and close the chuck lath cyclically. The available commercial software ABAQUS2021 is used for numerical study. The sensitivity test on conventional and auxetic sensors in different loading modes shows that the performance of the auxetic sensor in unidirectional and bidirectional loading modes is 272% and 130% better than the conventional sensor, respectively. It means that if the added area for the two sensors is closer to each other, the sensory performance of the two sensors will be more similar. Although the sensing performance of the two sensors in the three-directional loading mode is almost equal, the consumed strain energy required to deform the conventional sensor is 30 times more than that of the auxetic one.