Aluminum 3003 alloy used in the gas turbine and aerospace applications possesses medium bearing capacity. This technical paper reports the fabrication of Al 3003 alloy/TiO2 composites using friction stir processing. The weight fraction of reinforced TiO2 particles is varied between 0% and 6% with the increment of 1.5% in sequence. The fabricated specimens have been characterized by optical microscopy (OM), Energy dispersive X-ray spectroscopy (EDAX), Field emission scanning electron microscopy (FESEM), X-ray Diffraction analysis (XRD) and electron backscattered diagram (EBSD). Composite weld zone has witnessed the homogeneous distribution of TiO2 particles. The formation of such composite by reinforcement exhibits increase in the hardness and tensile strength of the weld. Corresponding strengthening mechanism is illustrated and correlated with the characterization studies. Fractography study shows brittle to ductile transformation with the addition of TiO2 particles.
Carbon nanotubes reinforced AA 7075 alloy was fabricated by powder metallurgy route. Multi-walled carbon nanotubes (MWCNTs) were synthesized by electric arc discharge method. Different mass fraction of CNTs was added to the AA 7075 and the powder mixtures were consolidated using uniaxial press. The consolidated samples were sintered at 600˚ C in inert atmosphere followed by hot compaction at 450˚ C. The electrochemical corrosion behaviour of AA 7075 and CNT reinforced AA 7075 was studied using Electrochemical Polarization Technique (ACM Gill) and Electrochemical Impedance Technique. The relative densities of the composites were measured. The phase analysis and surface morphology of the composites were done by XRD and scanning electron microscope (SEM). The corrosion behaviour of the composites and the possible mechanism for the effect of CNT in the properties have been studied in detail in this paper.
The Influence of plasma sprayed NiCr–Cr2O3 and Al2O3–40% TiO2 (A40T) coatings on Inconel 617 are investigated at 900 and 1000 °C under mixed salt environment for gas turbine applications. The results revealed that the plasma coated alloy exhibits lower mass change than bare alloy in the Na2SO4 and NaCl salt mixture with and without V2O5. The response to the experimental analysis is statistically evaluated using 23 factorial design. Further the exposed samples were analyzed by means of optical image, SEM, EDS and XRD results. The EDS and XRD analysis revealed that the oxides are rich in Ni and Mo on the surface of the samples. The coated samples exhibited better corrosion resistance in A40T when compared to NiCr–Cr2O3 coatings than bare alloy.
19 June 2014 in High Temperature Materials and Processes
An attempt is made to study the hot corrosion behaviour of Inconel 617 under mixed salt environment (Na 2 SO 4 , NaCl and/or V 2 O 5 ) at 900 and 1000 °C. The results were analysed and discussed with respect to mass change, XRD, optical image and SEM/EDAX. The oxide scales are enriched with Ni, Cr, Mo and Co at elevated temperatures. The presence of V 2 O 5 in the salt mixture is found to be the most influencing corrosion species for hot corrosion.
Ball joints used in steering linkages for load transfer generally provide articulation and rotation with degree of freedom. The function of the ball joints is to allow the suspension of the vehicle to move up and down, while at the same time it also allows the wheels to turn left or right. In order to increase the service life of the ball joints, manufacturers have resorted to various surface treatment and protective wear coatings. Wear on ball joint has been a perennial issue. Hence this investigation is focused to explore the possibility for wear reduction by spray pyrolysis technique employed on EN18 medium carbon steel coated with molybdenum disulphide as a strengthening agent. The adhesive bonding between the steel and coating was enriched by heat treating the coated material for 1 hr at 400 °C, which not only improved the wear property but also increased the hardness. Wear studies were conducted using pin on disc instrument at ambient temperature in dry condition. By varying process parameters namely the load, velocity and sliding distance identified by Response Surface Methodology (RSM), optimum wear rate was calculated. The Analysis of Variance (ANOVA) technique was utilized to forecast the influencing parameter in sequence which identified load as a prime parameter on increasing the wear rate followed by sliding distance and velocity. Regression equation employed, enabled the validation of the experimental results with an error less than 5%. FESEM analysis revealed the homogeneous distribution of coated layer on the base metal. The optimum values of wear rate have been achieved at 15N, 2.71m/s and 750 m for desired industrial application. Investigations with FESEM and EDAX ensured the presence of hard MoS2 particles in the base metal. Studies through ANOVA technique have conveyed that the sliding distance has greater impact on the wear rate.
The present work aims at investigating the collective function of thermo-reactive diffusion (TRD) and plasma-nitriding duplex coating (vanadium carbide (VC) and vanadium nitride (VC-VN)) on the wear resistance of AISI M2 axial-forming mandrel. TRD process was carried out in molten salt bath furnace at 1020 ± 25°C for 5–6 h and the samples were subjected to vacuum heat treatment process at 1150°C, followed by plasma-nitriding for 1 h at 550°C. Wear properties were examined by subjecting the VC and VC–VN-coated samples to wear test (pin on disc) at normal and elevated temperature (50° and 150°C) with lubrication. Phase composition, surface morphology and elemental mapping were studied through X-ray diffractometer, SEM and EDS analyses, respectively. Study found that the wear resistance of VC-coated samples was higher than VC–VN-coated samples and wear mechanisms for VC and VC–VN coated specimens were assessed to be abrasive and abrasive-oxidative in nature, respectively.