5 December 2018 in IEEE Sensors Journal
26 March 2019 in Journal of Lightwave Technology
A Michelson interferometer (MI) with gelatin coated for relative humidity (RH) measurement is proposed and demonstrated. It is fabricated by connecting the lead in/out single mode fiber (SMF), multimode fiber (MMF), triangular four core fiber (FCF) in a certain order. A gold film is deposited on the end face of the FCF as a reflector. A helical structure is fabricated by twisting the FCF under continuous arc discharging. Gelatin is coated onto the whole sensor to sense RH changes. When the RH of the external environment changes, both the refractive index (RI) and the size of the gelatin film changes, so the effective RI of the FCF cladding and the strain of the sensor changes accordingly, resulting in the resonance dip wavelength change in the interference signal. Such a probe is applied for RH measurement with a sensitivity of about -0.185 nm/%RH in the range from 45.0 %RH to 81.7 %RH. The response/recovery time of approximately 5.24/7.14 s, respectively.
24 July 2019 in IEEE Sensors Journal
Embedding of optical fiber sensors into materials to detect and monitor the deformation and damage of structures has attracted much attention recently. However, the embedding of optical fiber sensors into metallic materials is usually difficult due to lack of suitable technique, which does not damage the optical fiber during metal processing. In this paper, we introduced a very high power ultrasonic additive manufacturing (UAM) for producing metallic structure optical fiber sensors. Single-mode optical fibers (SMFs) were successfully embedded in aluminum (Al 1100) matrix by this technique. Tensile strain experiments were performed by a fiber optical white-light interferometric sensing system, and the effect of consolidation contact pressure of UAM on the output strain-applied strain relation was examined systematically. As the appropriate contact pressure of 1300 to 1350 N was taken, the excellent and reliable out strain-applied strain relations were obtained. These results demonstrate that the UAM produced optical sensor like a “nervous system” is capable of monitoring the health condition of metallic structural device.
30 July 2019 in IEEE Sensors Journal
A quasi-distributed directional bending sensor based on fiber Bragg gratings (FBGs) array in triangle-four core fiber (TFCF) is proposed and experimentally demonstrated. The proposed sensor was composed of a single mode fiber (SMF) and a TFCF. A piece of TFCF is heated by a thermal diffusion technique (TDT) to fabricate an integrated coupler, which couples the optical power from central core into the side cores. Considering the size of the Gaussian beam and the effective power distribution on the cross section of excimer laser, we fabricated FBGs samples by a defocusing phase mask method. We fabricated some FBGs array samples in TFCF with peak wavelengths in the range from 1528 nm to 1566 nm with a step of 4 nm. The error and variance of peak wavelengths and reflectivity are also measured. Obviously, the consistency of wavelength and strength are satisfactory. The curvature, temperature, and strain responses of FBG array samples with the central core and side cores are studied. Based on the unique characteristics of the proposed sensor, cross-sensitivity of temperature, and strain can be solved by subtracting the wavelength changes of side cores from that of central core. In addition, by adding temperature compensating sensor, we analyzed the combined standard uncertainty for simultaneous measurement of curvature, temperature, and strain. The proposed sensor have high potential to monitor the deformation of the smart wing on the spot and provide information for the flight control system to evaluate the aerodynamic performance of flight conditions.
25 October 2019 in IEEE Sensors Letters
15 June 2023 in IEEE Sensors Journal
The limit of Raman spectroscopy probe based on the traditional objective lens, such as integration difficulties, is the primary motivation to find better alternatives. Due to the potential of vertical integration and significant flexible design, a Raman spectroscopy fiber probe based on metalens at the fiber end facet is demonstrated. Using the "contact and separate" method, we successfully transferred the metalens to the end face of multimode fiber (MMF) to construct the Raman fiber probe with an ultrahigh numerical aperture (NA) of up to 0.66@air. In the case of the surface-enhanced Raman scattering (SERS) substrate composed of Au-plated anodic aluminum oxide (AAO) membrane with the same dry malachite green (MG), compared with the commercial Raman scattering light acquisition system based on an objective lens, our Raman signal intensity increases by at least 2.7 times at the Raman characteristic peak for MG. In the MG aqueous solution, the measurement with a limit of detection (LOD) of 10-9 mol/L@1616 cm-1 is realized. The proposed SERS sensing configuration based on the proposed Raman fiber probe and Au-covered AAO membrane also shows a broad application potential of real-time monitoring for other markers in the fields of food safety and environment detection.