This work introduces a new hybrid architecture combining a voltage-controlled oscillator (VCO)-based continuous-time (CT) delta-sigma modulator (DSM) with a noise-shaping (NS) successive approximation register (SAR) quantizer. The key innovation is an anti-aliasing filter (AAF) that bridges the VCO front-end with the NS-SAR quantizer, enabling the time-domain information to be directly sampled as the voltage-domain information. The hybrid architecture provides a high-order noise transfer function (NTF) while maintaining simple loop dynamics. The fabricated 28-nm CMOS prototype achieves 84.2-dB signal-to-noise-distortion ratio (SNDR) and 86.8-dB dynamic range (DR) within a 1-MHz bandwidth (BW) while consuming 1.62 mW at 100 MS/s. The corresponding Schreier SNDR figure of merit (FoM) is 172.1 dB. The core circuit occupies only 0.024 mm $^{2}$ . No calibration or coefficient tuning is required.
21 March 2025 in IEEE Journal of Solid-State Circuits
An integer-N digital-sampling phase-locked loop (PLL) based on a noise-shaping SAR (NS-SAR) analog-to-digital converter (ADC) breaks the quantization noise limitation of prior ADC-based phase detectors and enables the use of a lower resolution ADC quantizer and capacitive digital to analog converter (CDAC). Additionally, this improved ADC resolution reduces the phase-detector gain requirement and improves the lock performance. The 2nd-order noise-shaping of the NS-SAR ADC improves the time-to-voltage resolution of the phase detector by reducing in-band quantization noise and ADC input-referred noise (e.g., comparator noise). Measurements verify that noise shaping reduces the in-band noise by about 7 dB. The 28 nm CMOS prototype PLL operates at 4.3 GHz and consumes 13.7 mW. The measured rms integrated jitter from 1 kHz to 100 MHz is 133 fs.
29 September 2021 in IEEE Journal of Solid-State Circuits
A continuous-Time delta–sigma modulator (CT-DSM) excels at high-bandwidth (BW), high-dynamic-range analog-to-digital conversion. However, CT-DSMs suffer from PVT variation, high sensitivity to timing errors, and are restricted in sampling rate. This work proposes a hybrid-loop (HL) DSM architecture to mitigate the disadvantages of CT-DSM while providing similar performance. This work also introduces a bandpass time-interleaved noise-shaping (TINS) successive-approximation (SAR) architecture, which increases the sampling rate of TINS SAR. A prototype HL-DSM with bandpass TINS-SAR quantizer is built in 28-nm CMOS and occupies a die area of 0.09 mm 2 . The measured peak SNDR is 67.5 dB for a 100-MHz BW. The total power consumption is 13.4 mW at a sampling rate of 1.6 GS/s. The resulting Schreier FoM of 166.2 dB is comparable to state-of-the-art CT-DSM converters.
26 January 2026 in IEEE Journal of Solid-State Circuits
The noise-shaping (NS) successive approximation register (SAR) analog-to-digital converter (ADC) architecture is very power efficient but limited in bandwidth (BW). Time-interleaving (TI) expands the NS SAR BW with low hardware cost, but the conventional noise transfer function (NTF) zero placement leads to a marginal BW improvement with increasing NTF order. This work proposes a new hybrid structure utilizing cascaded (Ca) NS to decouple the oversampling rate (OSR) from the NTF order. A 6th-order bandpass (BP) cascaded time-interleaved (CaTI) NS SAR implements complex conjugate NTF zeros and requires only three interleaved channels and an OSR of $4\times $ . The prototype, fabricated in 28-nm CMOS, provides a 60-dB signal-to-noise-distortion ratio (SNDR) over a 175-MHz BW without calibration. The core circuit occupies 0.02 mm2 and consumes 3.38 mW at 1.4 GS/s. The corresponding Schreier SNDR figure of merit (FoM) is 167 dB. The experimental results demonstrate that the proposed CaTI NS SAR is a more robust and efficient alternative to conventional TI NS SAR ADC.