22 August 2022 in Energy & Environmental Science
Solid-state lithium–sulfur (Li–S) batteries have been recognized as a competitive candidate for next-generation energy storage systems due to their high energy density and safety. However, the slow redox kinetics between S and Li2S and the large volume change of sulfur during charge/discharge have hindered the development of solid-state Li–S batteries. We report a solid-state Li–S battery using a polymer-in-salt solid-state electrolyte, in which the sulfur is anchored in a polyacrylonitrile (PAN) substrate during cycling, avoiding the formation of Li2S and thus resulting in much faster redox kinetics and a smaller volume change than the conventional solid-state Li–S batteries. The quasi-intercalation reaction in the system is achieved with the assistance of the residual N,N-dimethylformamide (DMF), which helps strengthen the C–S bond. As a result, the solid-state Li-sulfurized PAN (SPAN) batteries have a superb rate capability at room temperature, even higher than those of liquid-state Li–S batteries, due to the faster redox kinetics and smaller volume change without solid–solid S to Li2S conversion which is present in liquid-state Li–SPAN batteries. This is the first report of the redox kinetics of solid-state Li–SPAN batteries being increased by changing the bond-strength of the C–S bond instead of using catalysts. This technique opens up new opportunities for designing high-performance solid-state Li–S batteries.
10 May 2024 in Journal of the American Chemical Society
9 January 2025 in Energy & Environmental Science
Solid polymer electrolytes (SPEs) are garnering significant interest for use in solid-state lithium metal batteries. However, a critical challenge in the rational design of electrolytes lies in ensuring interfacial compatibility, as well as navigating the trade-off between ionic conductivity and mechanical strength, which are essential for safety and cycling stability, particularly when utilizing high-energy-density electrodes. We report a π-conjugated polymer film, 4.1 μm thick, achieved through supramolecular oriented self-assembly, serving as a safe SPE host. Through π electron engineering with local delocalization, porous planar and rigid-rod molecular backbones were achieved, serving for ionic conduction and structural support, respectively. In addition to exhibiting a high ionic conductivity (7.7 × 10−4 S cm−1 at 25 °C along the aligned ion pathway), the π-conjugated polymer membrane also demonstrates extraordinary tensile strength (525 MPa) and supports robust cycling of Li symmetric cells for over 2500 hours. The utilization of a π-conjugated polymer host paves the way for the mass production of SPEs, promising safer and high-performance solid-state batteries.
13 November 2024 in Energy & Environmental Science
Despite the theoretical promise of attaining high energy densities, practical applications of lithium metal batteries (LMBs) remain hindered by the inadequacies of the electrode/electrolyte interface and unsatisfied cycling stability. Herein, a self-adsorption molecule with polar groups was designed and introduced in ether electrolyte, aiming to form a high-density and ordered molecular layer occupying active sites on the electrode surface, while restricting electrolyte molecule penetration into the interface. This self-adsorption molecule favors the formation of a robust anion-rich cathode/anode electrolyte interphase due to the change of the interfacial solvation structure, thus inhibiting solvent decomposition and enhancing interfacial stability. Consequently, the addition of this molecule into low-concentration ether electrolytes notably upgrades the electrochemical performance of the LiNi0.8Co0.1Mn0.1O2 (NCM811)||Li battery, which enables a high capacity retention of 87.2% after 250 cycles at 4.5 V. Moreover, the NMC811||Li pouch cells achieve stable cycling over 150 cycles with a capacity retention of 92.9% at a low negative/positive capacity ratio of 2.7 with a lean electrolyte. This interface passivation design strategy provides a promising path toward high-energy, durable, and safe rechargeable LMBs.
29 January 2024 in Journal of the American Chemical Society
12 April 2024 in Journal of Materials Chemistry A
Anode-free lithium metal batteries (AFLMBs) are considered as one of the most promising candidates for next-generation high-energy-density rechargeable lithium batteries. Improving the reversibility of lithium plating/stripping on bare anode current collectors is the key to enabling AFLMBs. Herein, we developed a high-current initiated formation strategy to improve the cycling stability of AFLMBs by regulating the Li nucleation and growth behavior. A great number of ultrafine Li nanospheres with uniform and dense distribution are deposited on the anode current collector during the initial Li deposition at very high current density (10–30 mA cm−2). These Li deposits serve as electrochemically active sites and manifest fast kinetics for lithium plating/stripping with enhanced exchange current density and successfully guide uniform dendrite-free Li nucleation/growth. Preferential decomposition of anions in the electrolyte under high current also induces the formation of robust inorganic-rich SEI, which facilitates the interfacial charge transfer and alleviates parasitic reactions. By simply changing the formation strategy, the average coulombic efficiency of Li‖Cu half cells is elevated from 96.8% to 98.5% at 1 mA cm−2 for 200 cycles and the capacity retention of the Cu‖LiFePO4 anode-free cell is impressively improved from 34.5% to 54.7% after 100 cycles. Besides, the time consumed for the formation process is effectively reduced by 10.5% after adopting the high-current initiated formation strategy, which could greatly improve the formation efficiency and holds great potential for practical application in AFLMBs.