Biological muscles exhibit a high level of integration, in which actuators, sensors and transmission elements can be included in one component. Artificial muscles or actuators refer to intelligent stimuli-responsive materials that could reversibly deform with the trigger of various external stimuli. These materials, which have attracted tremendous attention, produce natural muscle-like actuation performance and show promising applications in robotics. After an introduction of various actuator technologies that contribute to robotic applications, a comparative analysis of the main actuation parameter is provided. The comprehensive comparisons of each kind of artificial muscle are summarised, and the promising properties that are required in robotics are presented, which highlight the development of their actuation performances and the challenges that limit their further employments. Future developmental prospects and perspectives of artificial actuators are discussed.
12 September 2023 in IEEE Transactions on Industrial Electronics
Traditional robotic foot and ankle have received considerable attention for adaptive locomotion on complex terrain and land buffering ability. This study aims to develop a robotic ankle based on series elastic actuator with a parallel spring (SEAPS) by mimicking the two degree-of-freedom human ankle and related muscles. A unique four-SEAPS-based spring mechanism enhances motion adaptation and landing buffer. A dynamic model based on the SEAPS drive is presented, whereas a kinematic solution is realized. The bionic ankle has a wide range of motions with 30° in both the sagittal and frontal planes, which cover most of the human ankle motions. Four experiments were conducted to thoroughly characterize the capabilities. First, the static stiffness and the 2-D/3-D trajectory tracking performance of the proposed ankle were tested. Second, the angle sensing capacity under inclined road surface and the land buffering performance from a specific height were evaluated. The results show that the maximum 3-D motion tracking error is smaller than 2.3%, and the minimum sensing error of inclined road is smaller than 0.5%. The proposed ankle can closely track the 3-D walking trajectory of natural ankle joint with relative root-mean-square error well below 1.0%. Compared with no springs, landing buffer of the ankle with SEAPS can yield remarkable reduction in both peak ground reaction force (52.2%) and joint torque (57.9%). These findings prove that the SEAPS-based bioinspired robotic ankle exhibits high land buffering performance in an unstructured environment, and also well reproduces the human-like movement in terms of complex 3-D ankle motions.
Updated concrete construction robots are designed to optimize equipment operation, improve safety, enhance workspace awareness, and further ensure a proper working environment for construction workers. The importance of concrete construction robots has been constantly highlighted, as they have a profound impact on construction quality and efficiency. Autonomous vehicle driving monitoring has been widely employed in concrete construction robots; however, they lack clear relevance to the key functions in the building process. This paper aims to bridge this knowledge gap by systematically classifying and summarizing the existing concrete construction robots, analyzing their existing problems, and providing direction for their future development. The prescription criteria and selection of robots depend on the concrete construction process, which includes six common functional levels: distribution, leveling and compaction, floor finishing, surface painting, 3D printing, and surveillance. Misunderstood functions and the improper adjustment of construction robots may lead to increased cost, reduced effectiveness, and restricted application scenarios. Our review identifies current commercial and recently studied concrete construction robots to facilitate the standardization and optimization of robotic construction design. Moreover, this study may be able to guide future research and technology development efforts for autonomous robots in concrete construction.
Limb loss affects many people from a variety of backgrounds around the world. The most advanced commercially available prostheses for transfemoral amputees are fully active (powered) designs but remain very expensive and unavailable in the developing world. Consequently, improvements of low-cost, passive prostheses have been made to provide high-quality rehabilitation to amputees of any background. This study explores the design and evaluation of a smooth-locking-based bionic knee joint to replicate the swing phase of the human gait cycle. The two-part design was based on the condyle geometry of the interface between the femur and tibia obtained from magnetic resonance (MR) images of the human subject, while springs were used to replace the anterior and posterior cruciate ligaments. A flexible four-bar linkage mechanism was successfully achieved to provide not only rotation along a variable instantaneous axis but also slight translation in the sagittal plane, similar to the anatomical knee. We systematically evaluated the effects of different spring configurations in terms of stiffness, position, and relaxion length on knee flexion angles during walking. A good replication of the swing phase was achieved by relatively high stiffness and increased relaxation length of springs. The stance phase of the gait cycle was improved compared to some models but remained relatively flat, where further verification should be conducted. In addition, 3D printing technique provides a convenient design and manufacturing process, making the prosthesis customizable for different individuals based on subject-specific modeling of the amputee’s knee.
1 September 2020 in Journal of the Mechanical Behavior of Biomedical Materials