2 September 2019 in Advanced Functional Materials
As the size of materials, particles, and devices shrinks to nanometer, atomic, or even quantum scale, it is more challenging to characterize their thermal properties reliably. Scanning thermal microscopy (SThM) is an emerging method to obtain local thermal information by controlling and monitoring probe–sample thermal exchange processes. In this review, key experimental and theoretical components of the SThM system are discussed, including thermal probes and experimental methods, heat transfer mechanisms, calibration strategies, thermal exchange resistance, and effective heat transfer coefficients. Additionally, recent applications of SThM to novel materials and devices are reviewed, with emphasis on thermoelectric, biological, phase change, and 2D materials.
21 February 2011 in Langmuir
24 July 2015 in Nanoscale
This work discusses measurement of thermal conductivity (k) of films using a scanning hot probe method in the 3ω mode and investigates the calibration of thermal contact parameters, specifically the thermal contact resistance (Rth C) and thermal exchange radius (b) using reference samples with different thermal conductivities. Rth C and b were found to have constant values (with b = 2.8 ± 0.3 μm and Rth c = 44 927 ± 7820 K W−1) for samples with thermal conductivity values ranging from 0.36 W K−1 m−1 to 1.1 W K−1 m−1. An independent strategy for the calibration of contact parameters was developed and validated for samples in this range of thermal conductivity, using a reference sample with a previously measured Seebeck coefficient and thermal conductivity. The results were found to agree with the calibration performed using multiple samples of known thermal conductivity between 0.36 and 1.1 W K−1 m−1. However, for samples in the range between 16.2 W K−1 m−1 and 53.7 W K−1 m−1, calibration experiments showed the contact parameters to have considerably different values: Rth c = 40 191 ± 1532 K W−1 and b = 428 ± 24 nm. Finally, this work demonstrates that using these calibration procedures, measurements of both highly conductive and thermally insulating films on substrates can be performed, as the measured values obtained were within 1–20% (for low k) and 5–31% (for high k) of independent measurements and/or literature reports. Thermal conductivity results are presented for a SiGe film on a glass substrate, Te film on a glass substrate, polymer films (doped with Fe nano-particles and undoped) on a glass substrate, and Au film on a Si substrate.
28 January 2014 in Nanoscale
We report the formation of high aspect ratio nanoscale tree-shape silver networks in epoxy, at low temperatures (<150 °C) and atmospheric pressures, that are correlated to a ∼200 fold enhancement of thermal conductivity (κ) of the nanocomposite compared to the polymer matrix. The networks form through a three-step process comprising of self-assembly by diffusion limited aggregation of polyvinylpyrrolidone (PVP) coated nanoparticles, removal of PVP coating from the surface, and sintering of silver nanoparticles in high aspect ratio networked structures. Controlling self-assembly and sintering by carefully designed multistep temperature and time processing leads to κ of our silver nanocomposites that are up to 300% of the present state of the art polymer nanocomposites at similar volume fractions. Our investigation of the κ enhancements enabled by tree-shaped network nanocomposites provides a basis for the development of new polymer nanocomposites for thermal transport and storage applications.
14 December 2020 in Nanoscale Advances
Thermal conductivity measurements using Scanning Thermal Microscopy (SThM) usually involve heat transfer across the mechanical contact and liquid meniscus between the thermal probe and the sample. However, variations in contact conditions due to capillary effects at probe–sample contact and probe and sample wear due to mechanical contact interfere with accurate determination of the thermal conductivity. This paper presents measurements of thin film thermal conductivity using a SThM method employing a Wollaston probe in non-contact mode in synergy with detailed heat transfer analysis. In this technique, the thermal probe is scanned above the sample at a distance comparable with the mean free path of the ambient gas molecules. A Three-Dimensional Finite Element Model (3DFEM) that includes the specifics of the heat transfer between the sample and the probe in transition heat conduction regime was developed to predict the SThM probe thermal resistance and fit the thermal conductivity of the measured thin films. Proof-of-concept experimental in-plane thermal conductivity results for 240 nm and 46.6 nm Au films deposited on glass and silicon substrates were validated by experimental measurements of their electrical conductivity coupled with the Wiedemann–Franz law, with a discrepancy < 6.4%. Moreover, predictions based on a kinetic theory model for thin-film thermal conductivity agreed with the experimental results for the Au films with <6.6% discrepancy. To reduce the time and complexity of data analysis and facilitate experimental planning, an analytical model was also developed for the thermal transport between the Wollaston probe, ambient, and film-on-substrate samples. The accuracy of thin film thermal conductivity measurements using the analytical model was investigated using 3DFEM simulations. Fitted functions were developed for fast data analysis of thermal conductivity of thin films in the range of ∼100–600 W m−1 K−1 and thickness between ∼50–300 nm deposited on the two types of substrates investigated in this work, which yielded results with a discrepancy of 6–16.7% when compared to the Au films' thermal conductivity values.
9 May 2017 in Physical Chemistry Chemical Physics
Straining Bi2−xSbxTe3−ySeyactivates additional highly degenerate electronic bands near the Fermi level, providing over two-fold enhancement in thermoelectric power factor.