One of the greatest challenges in the commercialization of graphene and derivatives is production of high quality material in bulk quantities at low price and in a reproducible manner. The very limited control, or even lack of, over the synthesis process is one of the main problems of conventional approaches. Herein, we present a microwave plasma-enabled scalable route for continuous, large-scale fabrication of free-standing graphene and nitrogen doped graphene sheets. The method’s crucial advantage relies on harnessing unique plasma mechanisms to control the material and energy fluxes of the main building units at the atomic scale. By tailoring the high energy density plasma environment and complementarily applying in situ IR and soft UV radiation, a controllable selective synthesis of high quality graphene sheets at 2 mg/min yield with prescribed structural qualities was achieved. Raman spectroscopy, scanning electron microscopy, high resolution transmission electron microscopy, X-ray photoelectron spectroscopy and Near Edge X-ray-absorption fine-structure spectroscopy were used to probe the morphological, chemical and microstructural features of the produced material. The method described here is scalable and show a potential for controllable, large-scale fabrication of other graphene derivatives and promotes microwave plasmas as a competitive, green, and cost-effective alternative to presently used chemical methods.
An experimental and theoretical study on microwave (2.45 GHz) plasma enabled assembly of carbon nanostructures, such as multilayer graphene sheets and nanoparticles, was performed. The carbon nanostructures were fabricated at different Ar–CH4 gas mixture composition and flows at atmospheric pressure conditions. The synthesis method is based on decomposition of the carbon-containing precursor (CH4) in the “hot” microwave plasma environment into carbon atoms and molecules, which are further converted into solid carbon nuclei in the “colder” plasma zones. By tailoring of the plasma environment, a controlled synthesis of graphene sheets and diamond-like nanoparticles was achieved. Selective synthesis of graphene flakes was achieved at a microwave power of 1 kW, Ar and methane flow rates of 600 sccm and 2 sccm respectively, while the predominant synthesis of diamond-like nanoparticles was obtained at the same power, but with higher flow rates, i.e. 1000 and 7.5 sccm, respectively. Optical emission spectroscopy was applied to detect the plasma emission related to carbon species from the ‘hot’ plasma zone and to determine the main plasma parameters. Raman spectroscopy and scanning electron microscopy have been applied to characterize the synthesized nanostructures. A previously developed theoretical model was further updated and employed to understand the mechanism of CH4 decomposition and formation of the main building units, i.e. C and C2, of the carbon nanostructures. An insight into the physical chemistry of carbon nanostructure formation in a high energy density microwave plasma environment is presented.
An experimental and theoretical investigation of the axial structure of a surface wave (2.45 GHz) driven atmospheric plasma source in air with a small admixture (1%) of water vapor has been performed. Measurements of the gas temperature and of the intensities of the O(777.4 nm), O(844.6 nm), and O(630 nm) atomic lines and the molecular band versus input power and axial position were carried out. Amplitude and phase sensitive measurements have also been performed to derive the surface wave dispersion characteristics. The experimental results are analyzed in terms of a one-dimensional theoretical model based on a self-consistent treatment of particle kinetics, gas dynamics, and wave electrodynamics. The predicted gas temperature and emission line intensities variations with power and axial position are shown to compare well with experiment. “Hot” excited O atoms (with kinetic energy ) have been detected.
10 February 2020 in Physical Chemistry Chemical Physics
Free-standing N-graphene was synthesized using a microwave plasma-based method at atmospheric pressure conditions through a single step and in a controllable manner. Using ethanol and ammonia as precursors, N-graphene with low relative amount of bonded oxygen and low level of saturated sp3 carbon bonds was produced. Adjusting the injection position of the nitrogen precursor in the plasma medium leads to selectivity in terms of doping level, nitrogen configuration and production yield. A previously developed theoretical model, based on plasma thermodynamics and chemical kinetics, was further updated to account for the presence of nitrogen precursor. The important role of HCN attachment to the graphene sheets as the main process of N-graphene formation is elucidated. The model predictions were validated by experimental results. Optical Emission Spectroscopy was used to detect the emission of plasma generated “building units” and to determine the gas temperature. The plasma outlet gas was analyzed by Fourier-Transform Infrared Spectroscopy to detect the generated gaseous by-products. The synthesized N-graphene was characterized by Scanning Electron Microscopy, Raman and X-ray photoelectron spectroscopies.
The overall performance of a surface wave driven air-water plasma source operating at atmospheric pressure and 2.45 GHz has been analyzed. A 1D model previously developed has been improved in order to describe in detail the creation and loss processes of active species of interest. This model provides a complete characterization of the axial structure of the source, including the discharge and the afterglow zones. The main electron creation channel was found to be the associative ionization process N + O → NO+ + e. The NO(X) relative density in the afterglow plasma jet ranges from 1.2% to 1.6% depending on power and water percentage, according to the model predictions and the measurements. Other types of species such as NO2 and nitrous acid HNO2 have also been detected by mass and Fourier Transform Infrared spectroscopy. The relative population density of O(3P) ground state atoms increases from 8% to 10% in the discharge zone when the input microwave power increases from 200 to 400 W and the water percentage from 1% to 10%. Furthermore, high densities of O2(a1Δg) singlet delta oxygen molecules and OH radicals (1% and 5%, respectively) can be achieved in the discharge zone. In the late afterglow the O2(a1Δg) density is about 0.1% of the total density. This plasma source has a flexible operation and potential for channeling the energy in ways that maximize the density of active species of interest.
1 May 2008 in Plasma Sources Science and Technology