Ahmed Abbas Obaid

Ahmed Abbas Obaid

Auto-generated profile, based on publicly available information

Ahmed Abbas Obaid

Chemical Engineering Department, Faculty of Engineering, University of Al-Qadisiyah, Al-Diwaniya 58002, Iraq

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2022 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
MSMohammad Shamsi
Mohammad Shamsi
AOAhmed Abbas Obaid
Ahmed Abbas Obaid
SFSaman Farokhi
Saman Farokhi
ABAhmad Bayat
Ahmad Bayat

21 March 2024 in Energy
Verified
Journal Article
Closed access
MSMohammad Shamsi
Mohammad Shamsi
AOA.A. Obaid
A.A. Obaid
MVM. Vaziri
M. Vaziri
SMS. Mousavian
S. Mousavian
AHA. Hekmatian
A. Hekmatian
MBMohammad Bonyadi
Mohammad Bonyadi

13 April 2021 in Periodicals of Engineering and Natural Sciences (PEN)
Verified
Journal Article
Open access
PDF file
HAHusham M. Al.TAmeemi
Husham M. Al.TAmeemi
AOAhmed Abbas Obaid
Ahmed Abbas Obaid
HAHussein Hantoosh Alaydamee
Hussein Hantoosh Alaydamee
AAAli H. Abbar
Ali H. Abbar
Expulsion of cadmium from a simulated wastewater using CKD as adsorbent: Optimization with isotherm study

30 September 2025 in Al-Qadisiyah Journal for Engineering Sciences
Verified
Journal Article
Open access
PDF file
AHAli Flayyih Hasan
Ali Flayyih Hasan
AOAhmed Abbas Obaid
Ahmed Abbas Obaid
OAOmid Amanzadeh
Omid Amanzadeh
FJFalah Abdulhassan Jasim
Falah Abdulhassan Jasim
Biodiesel is a promising alternative to conventional fossil fuels, so effective catalysis is essential to enhance the efficiency and selectivity in biodiesel production. This article discusses one of the methods used to synthesize these catalysts and their effectiveness in biofuel production. A catalyst was synthesized from palm frond waste, which is abundant in Iraq. Palm frond dust acquired magnetic properties by adding iron (III) chloride by the impregnation method. Palm frond dust was carbonized for 3 h at 700 C°and then sulfonated using (H2SO4) depending on variable factors such as reaction time, temperature, and acid concentration. The change of these factors on the acidity value of the catalyst was studied. The catalyst was characterized using techniques such as FTIR, SEM, acid value, and BET. The study successfully prepared an effective magnetic catalyst with the possibility of recovery due to its magnetic properties. The surface area determined by BET was 585.12 m2/g, indicating a high specific surface area value. The highest expected acid value was 4.23 mmol/g at a reaction time of 2.6 h°, a temperature of 50 C°, and a concentration of 10 M.

1 January 2025 in International Journal of Polymer Science
Verified
Journal Article
Open access
AOAhmed Abbas Obaid
Ahmed Abbas Obaid
AAAli Khudhair Jabbar AL-HAMZAWI
Ali Khudhair Jabbar AL-HAMZAWI
RDReza Darvishi
Reza Darvishi
MVMohammad Vaziri
Mohammad Vaziri
In this study, a novel polyvinyl chloride (PVC)–based adsorbent was synthesized and functionalized with a Schiff base derived from 4,4 ′ ‐diaminodiphenyl ether and vanillin, followed by complexation with copper (II) nitrate nonahydrate, to effectively remove sulfamethoxazole (SMX) from aqueous solutions. The final composite, designated as PVC‐Cu‐SbDEV, was obtained through postsynthetic coordination of the Schiff base–modified PVC with Cu(II) ions. The structural and surface characteristics of the adsorbent were thoroughly characterized using FTIR, SEM, EDX, BET, and TGA analyses. Parametric studies including solution pH, contact time, initial SMX concentration, and temperature were conducted to determine optimal adsorption conditions. Under the optimized conditions—pH 6, contact time of 120 min, initial SMX concentration of 80 mg L −1 , and temperature of 30°C—the adsorbent exhibited a maximum adsorption capacity of 165 mg g −1 and a removal efficiency of 68%. Isothermal and kinetic analyses indicated that the adsorption process followed the Freundlich isotherm model and pseudo‐second‐order kinetics, suggesting a heterogeneous adsorption surface and chemisorption as the dominant mechanism. Thermodynamic evaluations further revealed that the process was endothermic and spontaneous, with values of Δ H ° = +29.5 kJ mol −1 , Δ G ° ranging from −1.2 to −3.1 kJ mol −1 , and Δ S ° = 0.105 kJ mol −1 K −1 . Overall, the PVC‐Cu‐SbDEV adsorbent demonstrated significant efficiency for SMX removal, showing a substantial improvement in performance compared to unmodified PVC.