Pawel Lipinski

Pawel Lipinski

Auto-generated profile, based on publicly available information

Pawel Lipinski

Metz

Research Focus & Metrics

Academic Career Length

45Years (1982-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 1989 in International Journal of Plasticity
Verified
Journal Article
Closed access
PLP Lipinski
P Lipinski
MBM Berveiller
M Berveiller

1 May 2012 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
ABA. Barbas
A. Barbas
ABA.-S. Bonnet
A.-S. Bonnet
PLP. Lipinski
P. Lipinski
RPRaphael Pesi
Raphael Pesi
GDG. Dubois
G. Dubois

1 March 2007 in Medical Engineering & Physics
Verified
Journal Article
Closed access
MDM. Daas
M. Daas
GDG. Dubois
G. Dubois
ABA.S. Bonnet
A.S. Bonnet
PLP. Lipinski
P. Lipinski
CRC. Rignon-Bret
C. Rignon-Bret
The aim of this study was to evaluate the influence of the retention mechanism on the behavior of a mandibular implant-retained overdenture (IRO) during the simulation of mastication. Therefore, a complete three-dimensional finite element model of a mandible with its IRO was developed. The geometry of the edentulous mandible and overdenture was generated from computed tomography. Two MKIII implants (Nobel Biocare) with ball abutments and Dalbo Plus (Cendres et Métaux) attachments were placed in the canine areas. Three foodstuff positions were analyzed for two retention mechanisms, "resilient" or "rigid". Special attention was given to the modeling of the mandibular environment and of the existing contact between the different components. A probable muscular action was determined following the minimal work principle. The food-crushing force was provided by masseters with a two-third/one-third ratio between working and non-working sides. The "resilient" configuration provided a wider contact area between the mucosa of the denture bearing area and the prosthesis. An increase of the mastication force transiting through the mucosa was also noted and lower stresses were observed in the bone surrounding implants. Resilient attachments allowed for an increase of the mastication load transiting through denture bearing surface. Furthermore, this study proposed an accurate model of the mandibular IRO, including its environment and faithful behavior reproduction.

22 April 2009 in Medical Engineering & Physics
Verified
Journal Article
Closed access
ABA.S. Bonnet
A.S. Bonnet
MPM. Postaire
M. Postaire
PLP. Lipinski
P. Lipinski
The aim of this work was to study the biomechanical behavior of a "All-on-four" implant-supported prosthesis through a finite element analysis using either isotropic or anisotropic properties of bone. The influence of foodstuff position during mastication was also analysed. A three-dimensional finite element model of a mandible with a prosthesis supported by four implants was developed. The geometry of the edentulous mandible and prosthesis was generated from computed tomography. Four MKIII implants (two vertical and two tilted) were modeled. The bone elastic properties used in the anisotropic simulations were orthotropic. The comparison of isotropic and anisotropic models was carried out in the loading condition of mastication with a foodstuff positioned on molar. Three distinct configurations, corresponding to three foodstuff positions, were then studied. MSC/Marc code was used to perform all computations. Significant differences in stress, strain, and strain energy densities were found in the comparison of isotropic and orthotropic models. Molar position was revealed to be the most critical one, from a stress and strain level point of view, for implants and framework and consequently for peri-implant bone. It was also observed that implant tilting leads to high stress concentrations in bone for the "All-on-four" concept. This study showed that the anisotropic behaviour of bone cannot be neglected in the numerical simulations. The actual design of the prosthesis is not optimal concerning the capacity of all metallic parts to support loads. Finally, it was demonstrated that the tilting of implants induced a high stress level at bone-implant interface.

1 November 2006 in International Journal of Machine Tools and Manufacture
Verified
Journal Article
Closed access
ALA. Lefebvre
A. Lefebvre
PVP. Vieville
P. Vieville
PLP. Lipinski
P. Lipinski
CLC. Lescalier
C. Lescalier

1 November 2006 in International Journal of Machine Tools and Manufacture
Verified
Journal Article
Closed access
LCLuis Ricardo Castro
Luis Ricardo Castro
PVPascal Viéville
Pascal Viéville
PLPaul Lipinski
Paul Lipinski