Bakhtiyar Q. Khawaja Al Harki

Bakhtiyar Q. Khawaja Al Harki

Auto-generated profile, based on publicly available information

Bakhtiyar Q. Khawaja Al Harki

Department of Surveying, Akre Technical Institute, Akre University for Applied Sciences, Duhok, Kurdistan Region, Iraq

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 April 2026 in Dasinya Journal for Engineering and Informatics
Verified
Journal Article
Open access
IMIsmael A. Muhammed
Ismael A. Muhammed
ARAbdullah M. Rashed
Abdullah M. Rashed
SKSherzad Waisy Khalid
Sherzad Waisy Khalid
BHBakhtiyar Q. Khawaja Al Harki
Bakhtiyar Q. Khawaja Al Harki
Plastic waste is a new environmental threat and potential resource at the same time. The use of plastic waste polymer polypropylene fibers in asphalt mixtures is a good eco-solution that increases the pavement's lifetime. With traffic rising, forcing the needs in classic asphalt for improved durability. The study aimed to investigate the reinforcement characteristics of plastic fibers of four different lengths in cm (FL1, FL2, FL3, and FL4), represented by 1 cm, 2 cm, 3 cm, and 4 cm, added to virgin asphalt mixtures (0.3% by total mix). Results by Marshall stability, Marshall stiffness, indirect tensile strength (ITS), moisture susceptibility (TSR), and deformation strength testing were quantified. The results showed that the stability of Marshall increased until the FL3 length, with FL1 and FL2 showing 23% and 10% enhancement, respectively, followed by a marginal decrease to FL4 as plastic fiber was introduced. Additionally, the moisture resistance improved with the fiber length, and the TSR values were significantly higher than that of the virgin mix. Regarding rutting resistance, fiber reinforcements greatly lowered deformation, most especially when fiber lengths were shorter. Generally, durability, moisture damage resistance, and rutting resistance are enhanced on a scale of 1–2 cm fiber length, hence being the most convenient quality for asphalt mixtures. In this research, the optimum length of PP fiber was specified to improve mechanical properties, and plastic waste was reused as a resource for sustainable road construction, both in accordance with SDG 9 and SDG 12 of the Sustainable Development Goals.

12 July 2026 in Dasinya Journal for Engineering and Informatics
Verified
Journal Article
Open access
PDF file
HGHEJA GHAZI
HEJA GHAZI
ZAZiyad N. Aldoski
Ziyad N. Aldoski
IMIsmael Mohammed
Ismael Mohammed
ARAbdullah Rashed
Abdullah Rashed
BHBakhtiyar Al Harki
Bakhtiyar Al Harki
In this work, the mechanical properties and deformation behavior of Hot Mix Asphalt (HMA) reinforced with Glass Fiber (GF) are analyzed. The focus was mainly on determining the effects of different GF content on the behavior/ stability/ stiffness/ permanent deformation of asphalt concrete in wearing courses. The experimental protocol was based on asphalt Al-Daurah cement (40/50 penetration grade) and crushed aggregates obtained from Kavin Company (Zakho, Duhok), with a nominal maximum aggregate size (NMAS) of 12.5 mm, as per ASTM D3515. The study was carried out in two stages. The Optimum Asphalt Content (O.A.C.) was determined to be 5.1% using Marshall mix techniques. In phase two, 5 mixtures were made together with the dry mixing method, adding (GF) at 0% (Control), 0.3%, 0.5%, 0.7%, and 0.9% by weight of the mix. Experimental results showed improved structural integrity of the asphalt when glass fibers were applied. The Marshall Stability was at its maximum at 0.5 % GF (12.5 kN), 25 % higher than the control mixture. Additionally, the Kim Test was used to probe the high-temperature effect, and the Deformation Strength (SD) level increased by ≈ 50% at the same dosage (2.706 MPa > 4.048 MPa). The maximum Marshall Stiffness was 3.8 kN/mm at 0.5% GF, indicating superior shear resistance. Yet, fiber levels above 0.5% lead to decreased performance due to fiber agglomeration and poor workability. The Optimum Glass Fiber Content (O.GF.C.) is 0.5% GF for improving both the durability and rutting resistance of flexible pavements in hot weather.