Darwin Lau

Darwin Lau

Auto-generated profile, based on publicly available information

Darwin Lau

The Chinese University of Hong Kong

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 February 2022 in IEEE Transactions on Robotics
Verified
Journal Article
Closed access
CSChen Song
Chen Song
DLDarwin Lau
Darwin Lau
The control of cable-driven robots is challenging due to the system’s nonlinearity, actuation redundancy, and the unilaterally bounded actuation constraints. To solve this problem, a workspace-based model predictive control (W-MPC) scheme is proposed, which combines the online model predictive control with offline workspace analysis. Using the workspace, a set of convex constraints can be generated for a given reference trajectory. This can then be used to formulate a convex optimization problem for the online W-MPC. Meanwhile, strict recursive feasibility and stability are obtained by taking advantage of the predictive feature of MPC. To demonstrate the effectiveness of the proposed W-MPC, simulation was performed on a 2-link planar cable-driven robot and a spatial cable-driven parallel robot for both nominal and non-nominal scenarios. Hardware experiment was also carried out using a 3 degree-of-freedom planar cable robot. The results show that the controller is efficient and effective to perform motion tracking with the cable force constraints satisfied despite the existence of various model uncertainties.

9 October 2018 in IEEE Transactions on Robotics
Verified
Journal Article
Closed access
GAGhasem Abbasnejad
Ghasem Abbasnejad
JEJonathan Eden
Jonathan Eden
DLDarwin Lau
Darwin Lau
This paper presents a new generalized ray-based approach to the generation and representation of the wrench-closure workspace (WCW) for cable-driven robots (CDRs). Existing WCW studies have yet to address two significant problems, first is the lack of a generalized approach to generate the WCW with continuity information for all degrees-of-freedom (DoFs) and arbitrary CDRs, and second is a workspace representation for higher DoF robots. The proposed work addresses these issues using a generalized ray-based lattice WCW generation approach that can be applied in all DoFs. Furthermore, a new graph workspace representation is introduced with a range of advantages in the way CDR workspace can be visualized and studied. Such a representation is powerful since it: can be used for any other type of workspace beyond the WCW; can be visualized in two-dimensions regardless of the number of DoFs of the system; allows metric information to be included; and opens up the use of well-established graph theory techniques to study the workspace. Through three different CDR examples, a 3-DoF planar cable-driven parallel robot (CDPR), a 4-DoF multilink robot, and a 6-DoF CDPR, the characteristics and advantages of the proposed method are highlighted.

1 May 2018
Verified
Conference Paper
Closed access
YWYulong Wu
Yulong Wu
HCHung Hon Cheng
Hung Hon Cheng
AFAdam Fingrut
Adam Fingrut
KCKristof Crolla
Kristof Crolla
YYYeung Yam
Yeung Yam
DLDarwin Lau
Darwin Lau
Robotic building construction has had significant advances in the recent decades, but also has various limitations. In particular, construction typically requires a robot to operate within a large space for long hours and be able to transport between sites. Cable-driven parallel robots (CDPRs) show strong potentials within the automation of construction due to its desirable characteristics, such as high payload-to-weight ratio, transportability, scalability and reconfigurability. This paper proposes a simulation-based analysis, design and pre-execution verification for a cable-driven brick structure building system (CU-Brick), among which a way to determine the buildable workspace where the construction could be constructed is proposed. Simulations are used to do the workspace analysis, design of the brick structure within the workspace and also verification that the motions can be executed. Using this simulation approach, real demonstrations have been performed to show that indeed the system is able to construct the brick structures safely and consistently.

3 October 2023 in IEEE Transactions on Robotics
Verified
Journal Article
Open access
HCHung Hon Cheng
Hung Hon Cheng
DLDarwin Lau
Darwin Lau
This article proposes a novel method to determine the optimal cable attachment configuration for reconfigurable cable-driven parallel robots (RCDPRs) considering different workspace conditions. It is shown that wrench-feasible, wrench-closure, and interference-free conditions can be formulated into inequality constraints by considering the cable attachment points as polynomial functions or variables. Furthermore, the proposed method determines the optimal cable attachment location that minimizes the cable force or maximizes the tension factor kinematically at each pose. The proposed formulation can be resolved by different optimization techniques, such as semidefinite programming relaxation and multivariable gradient-based optimization solvers. The proposed approach can be implemented on RCDPRs from low to high degrees-of-freedom and a wide range of obstacles. The proposed formulation can be widely applied for different reconfiguration mechanisms, such as rails, unmanned ground vehicle (UGV), and unmanned aerial vehicle (UAV).

1 December 2016
Verified
Conference Paper
Closed access
DLDarwin Lau
Darwin Lau
JEJonathan Eden
Jonathan Eden
YTYing Tan
Ying Tan
DODenny Oetomo
Denny Oetomo
The study of cable-driven parallel robots (CDPRs) has attracted much attention in recent years. However, to the best of the authors' knowledge, no single software platform exists for researchers to perform different types of analyses for CDPRs of arbitrary structure. In this paper, the Cable-robot Analysis and Simulation Platform for Research (CASPR) of CDPRs is introduced. Using this platform, arbitrary types and structures of CDPRs, such as single and multi-link CDPRs, can be studied for a wide range of analyses, including kinematics, dynamics, control and workspace analysis. CASPR achieves this using a general CDPR model representation and an abstracted software architecture. Moveover, CDPRs can be defined using Extensible Markup Language (XML) with out-of-the-box availability of an extensive range of robots and analysis tools. The open-source platform aims to provide both a communal environment for the researchers to use and add models and algorithms to. The example case studies demonstrate the potential to perform analysis on CDPRs, directly compare algorithms and conveniently add new models and analyses.

18 September 2019 in IEEE Robotics and Automation Letters
Verified
Journal Article
Closed access
ZZZeqing Zhang
Zeqing Zhang
HCHung Hon Cheng
Hung Hon Cheng
DLDarwin Lau
Darwin Lau
This paper introduces a novel approach to verify the feasibility of curved trajectories under both the interference free (IFC) and wrench-closure (WCC) conditions for spatial cable-driven parallel robots (CDPRs). Existing ray-based methods can only be used either for translation or single degree-of-freedom (DoF) motion, limiting its use to verify the motion of practical trajectories. In this work, the trajectory representation proposed allows the IFC and WFC for the entire trajectory to be verified by simply solving a set of univariate polynomial equations. The translation motion is expressed as polynomial time parametric functions and the orientation motion is defined using a spherical linear interpolation (SLERP) in the quaternion representation for a desired start and end orientation. It is then shown that for the proposed trajectory representation, the IFC and WFC can be verified by solving a set of univariate polynomial equations. Moreover, the exact degree of the resulting polynomial equations are derived for a 6-DoF spatial CDPR. Simulation on a range of different trajectory forms, from linear, quadratic and cubic paths to higher degree functions, show the effectiveness of the method. Finally, comparison with the well-accepted point-wise method shows that the proposed method is more efficient, accurate and ensures the solution continuity.