27 May 2021 in Physical Review Fluids
The accurate measurement of flows and aerodynamic characteristics around a bluff body has been a challenging task due to the existence of interference between the wake and mechanical model supports in wind-tunnel experiments. The present study focuses on a freestream-aligned circular cylinder with an extremely low fineness ratio (the ratio of the axial length to diameter) ranging from 0.30 to 0.50, which has never been investigated without interference from a mechanical model support. We employed a magnetic suspension and balance system to eliminate interference from the model support and measured the drag and velocity fields in the diameter-based Reynolds number between and . As the fineness ratio decreases below 1.50, the size of the recirculation bubble increases and the velocity distribution on the central axis inside the bubble gradually converges to that of the circular disk. Furthermore, large-eddy simulations were performed in the Reynolds number of , whose drag coefficient agrees well with experiments. Based on those results, it was found that the drag coefficient monotonically converges to that of the circular disk without local maximum. This study revealed that in the low-fineness-ratio regime (0.10–0.50), a critical geometry, at which the drag coefficient shows a local maximum, does not exist in the circular cylinder. Subsequently, unsteady flow analyses were performed, where two characteristic frequencies, i.e., and 0.155, were identified from power spectral densities of the drag coefficient and the pitching moment coefficient. The associated flow structures are then extracted by a phase-averaging procedure, where the phase-averaged flows with represent the recirculation bubble pumping while the phase-averaged flows with show nonaxisymmetric structures inside the recirculation bubble.
8 January 2021 in Experiments in Fluids
1 June 2022 in Physics of Fluids
In the present study, characteristics of a shear layer around a freestream-aligned circular cylinder and the relationship between the shear layer motion and the aerodynamic force were investigated under supportless condition. A 0.3-m magnetic suspension and balance system was employed, and experiments were conducted without a mechanical supporting device. Velocity fields were measured using particle image velocimetry with a sufficient temporal and spatial resolution, and high-frequency velocity fluctuations caused by small Kelvin–Helmholtz (KH) vortices were captured. The power spectral densities of velocity fluctuations represent phenomena such as KH vortex convection, vortex pairing, and convection of multiple vortices. Furthermore, fluctuations of the shear layer position were investigated. The results illustrate that the dominant frequency of the shear layer position is lower than the frequency of the velocity, and it shows good agreement with the characteristic frequency of lift force fluctuations. The present results together with the report in the previous study illustrate that the pressure fluctuations are considered to drive both fluctuations of the shear layer position and lateral aerodynamic force.
1 January 2024 in Physics of Fluids
Base pressure fluctuations associated with the large-scale wake structures behind a freestream-aligned circular cylinder and aerodynamic force fluctuations related to them are experimentally investigated in the wind tunnel tests. Measurements at ReD=6.97×104 and 1.04×105 were conducted using pressure-sensitive paint (PSP) and a magnetic suspension and balance system (MSBS) for creating a supportless condition. The obtained pressure fields were mainly analyzed by a modal decomposition combining azimuthal Fourier decomposition and proper orthogonal decomposition (POD). The pressure fluctuations caused by large-scale vortex shedding were observed from the results of frequency analysis for mode coefficients. The states of the fluctuations were classified into three patterns, which are anticlockwise/clockwise circular and flapping patterns. These patterns have been observed in the previous studies for velocity fluctuations in the wake of a freestream-aligned circular cylinder. The conditional sampling analysis revealed that the trend in the amplitude of the pressure fluctuations is different by the state, and the flapping pattern causes a large pressure difference across the cylinder axis. Furthermore, the relationship between the antisymmetric pressure fluctuations and lift fluctuations, which act in the lateral direction of the cylinder, is confirmed.
1 March 2024 in Journal of Fluid Mechanics
The relationships between characteristic large-scale wake structures appearing behind a free-stream-aligned circular cylinder are investigated and discussed from the velocity field obtained by wind tunnel tests. The tests were conducted under a supportless condition using a magnetic suspension and balance system and stereo PIV measurements at a Reynolds number of $3.46\times 10^4$ . The velocity fields were analysed with a modal decomposition combining azimuthal Fourier decomposition and proper orthogonal decomposition. The wake behind the free-stream-aligned circular cylinder with three different fineness ratios of 1.0, 1.5 and 2.0 was investigated, and the wake structures in a non-reattaching flow formed by the cylinder at a fineness ratio of 1.0 are mainly discussed in the present study. Four characteristic large-scale wake structures of the recirculation bubble pumping, azimuthal shear mode, large-scale vortex shedding and streaks are identified and mainly focused on in the present study. The state of the vortex shedding is classified into three: anticlockwise/clockwise circular and flapping patterns. Each state has a relationship with the azimuthal shear mode and it tends to appear when the state is circular. Furthermore, from the analysis of the relationship between modes, the recirculation bubble pumping is found to be related to the vortex shedding position in the radial direction and the strength of the streaks. Particularly, analysis of causality shows that the recirculation bubble pumping is affected by them in the low-frequency range.
1 February 2023 in Review of Scientific Instruments
A new model-position-sensing method for the levitation of models with a low fineness ratio (ratio of the longitudinal length to the diameter) in a magnetic suspension and balance system (MSBS) is proposed. MSBS is an ideal model-support device for wind-tunnel testing, which enables the study of flow fields around blunt bodies without flow disturbances introduced by mechanical support devices, with the aerodynamic forces determined from the magnetic forces using a pre-calibrated relationship. The new method allows wind tunnel experiments without mechanical supports with a low fineness ratio model. This method adopts two line sensors placed parallel to the central axis of the model image and measures the position with a resolution finer than 0.06 mm or deg even for thin model geometries. In addition, measurement errors were reduced by correcting a second-order term in the depth direction of the camera. A low fineness ratio circular cylinder model was levitated following sensor calibration. The model was supported in conditions with and without freestream flow. This position measurement method was also applied to a reentry capsule model. The model was levitated while keeping its position and attitude stabilized near the origin.