This work presents a molecular dynamics simulation study on the interfacial characterization of graphene/epoxy nanocomposites. In polymeric nanocomposites, the thermo-mechanical properties of a system strongly depend on the characteristics of the interphase region between the matrix and the inclusions. The first step in the characterization of this interphase is to distinguish its border limit (i.e., the interphase thickness). Here, we present a methodology to systematically quantify the interphase thickness based on analyzing the variation of the local mass density profile. To this end, three functions (average accumulated mass density, accumulated standard deviation (ASD) and its first derivative) are successively applied on the local mass density profile. Using this procedure, the interphase limit can be easily detected regardless of the oscillatory nature of the local mass density. The effect of the epoxy crosslinking density and number of graphene layers on the interphase thickness is then investigated, and the results are analyzed by studying the interaction energies, polymer dynamics and distribution quality of reacted and unreacted components, as well as conformational changes of the polymer chains in the interphase region. The results reveal that the crosslinking density is the most influential parameter on the interphase thickness: the higher the crosslinking degree, the thicker the interphase region. To a lower extent, the interaction energy has also an effect on the interphase thickness since there is an inverse relationship between the interaction energy and the crosslinking density in our case study. Overall, the reported findings highlight useful insights into the detection and properties of the interphase region in thermoset composites.
Froth flotation is the most versatile process in mineral beneficiation, extensively used to concentrate a wide range of minerals. This process comprises mixtures of more or less liberated minerals, water, air, and various chemical reagents, involving a series of intermingled multiphase physical and chemical phenomena in the aqueous environment. Today's main challenge facing the froth flotation process is to gain atomic-level insights into the properties of its inherent phenomena governing the process performance. While it is often challenging to determine these phenomena via trial-and-error experimentations, molecular modeling approaches not only elicit a deeper understanding of froth flotation but can also assist experimental studies in saving time and budget. Thanks to the rapid development of computer science and advances in high-performance computing (HPC) infrastructures, theoretical/computational chemistry has now matured enough to successfully and gainfully apply to tackle the challenges of complex systems. In mineral processing, however, advanced applications of computational chemistry are increasingly gaining ground and demonstrating merit in addressing these challenges. Accordingly, this contribution aims to encourage mineral scientists, especially those interested in rational reagent design, to become familiarized with the necessary concepts of molecular modeling and to apply similar strategies when studying and tailoring properties at the molecular level. This review also strives to deliver the state-of-the-art integration and application of molecular modeling in froth flotation studies to assist either active researchers in this field to disclose new directions for future research or newcomers to the field to initiate innovative works.
This study attempts to comprehensively investigate the effects of multi-walled carbon nanotubes (MWCNTs) on the AC and DC electrical conductivity of epoxy nanocomposites. The samples (0.2, 0.3, and 0.5 wt. % MWCNT) were produced using a combination of ultrason and shear mixing methods. DC measurements were performed by continuous measurement of the current-voltage response and the results were analyzed via a numerical percolation approach, while for the AC behavior, the frequency response was studied by analyzing phase difference and impedance in the 10 Hz to 0.2 MHz frequency range. The results showed that the dielectric parameters, including relative permittivity, impedance phase, and magnitude, present completely different behaviors for the frequency range and MWCNT weight fractions studied. To better understand the nanocomposites electrical behavior, equivalent electric circuits were also built for both DC and AC modes. The DC equivalent networks were developed based on the current-voltage curves, while the AC equivalent circuits were proposed by using an optimization problem according to the impedance magnitude and phase at different frequencies. The obtained equivalent electrical circuits were found to be highly useful tools to understand the physical mechanisms involved in MWCNT filled polymer nanocomposites.
17 October 2017 in Science and Engineering of Composite Materials
Various nano- and micro-sized fillers can be integrated into polymers to enhance their flame-retardant performance. In this work, a diglycidyl-ether bisphenol A epoxy was used as the matrix and nanostructured silica aerogel (AG) and ammonium polyphosphate (APP) microparticles were investigated as fillers to improve the flame-retardant and thermal properties of the epoxy. The anti-flame, thermal, and mechanical properties of the composites were investigated for different volume fractions of filler particles. It was found that APP decreased the burning rate while significantly improving the thermal stability. To investigate the flame resistant properties of combined AG and APP, an optimized ratio of AG and APP was added to the epoxy, leading to a stable flame-retardant epoxy with a low thermal conductivity and improved glass transition temperature ( Tg ). The synergy between the AG and APP in composite samples resulted in an interesting burning behavior where sample core was relatively less deteriorated compared with the samples containing only APP or AG. This was attributed to the decrease of thermal conductivity due to the addition of AG. Lastly, samples containing APP showed the highest limiting oxygen index percentage and it was found that only small amounts of APP are required to make the epoxy flame-retardant.