Dielectric barrier discharge (DBD) plasma actuators with an asymmetric, straight edge electrode configuration generate a wall-bounded jet without moving parts. Mechanistic description of the interaction between the Coulombic forces and fluid motion as a function of DBD parameters remains unclear. This paper presents an experimental investigation of DBD actuators, including electrical current associated with microdischarges, plasma volume and the wall jet momentum over a range of alternating current (AC) frequencies (0.5–2 kHz) and peak-to-peak voltages up to 19.5 kV. Discharge current is measured with a high temporal resolution, plasma volume is characterized optically and the momentum induced by the DBD wall jet is computed based on the axial velocities measured downstream of the actuator using a custom-built pitot tube. Discharge current analysis demonstrated asymmetry between the positive and negative semi-cycle; both currents yielded a power–law relationship with empirical fitting coefficients. Plasma length varies linearly and volume quadratically with voltage. Although plasma length reached an asymptotic value at a higher frequency, the plasma volume grows due to the increasing height of the ionization region. In a simple two-dimensional configuration, the DBD wall jet momentum shows near-linear dependency with discharge current in the range of voltages and frequencies considered in this work. The presented empirical model characterizes the DBD wall jet momentum and the discharge current based only on the AC inputs. With the estimation of plasma volume, the model can be applied for determining more realistic boundary conditions in numerical simulations.
Infectious viruses can survive on surfaces for hours; they can be responsible for the fomite transmission mechanism of many diseases. We report the development and evaluation of a compact nonthermal plasma (NTP) flow reactor and its application for disinfection of surfaces. The concentric flow reactor produces a high concentration of reactive species by ionizing air flow passed through the reactor; the ionized jet exiting the reactor is impinged on the surface, exposing pathogens to high concentrations of reactive oxygen and nitrogen species. The reactor performance is characterized by measuring ozone concentration for various geometries and operating conditions. The ozone concentration reaches saturation at the exit for electrical power input above 100 W. The approach was tested for the inactivation of MS2 bacteriophage on surfaces with varied exposure times. We observed a 1.3-log reduction in viable virus counts at the exposure of 30 s and a 5.3-log reduction at 120-s exposure. The ozone production rates suggest that the reactor can be scaled to operate at higher flow rates, producing a concentration of reactive species sufficient for virus inactivation.
1 July 2025 in Plasma Sources Science and Technology
Dielectric barrier discharge (DBD) plasma actuators generate an electrohydrodynamic (EHD) force through the ionization and acceleration of charged species. Most active flow control DBD applications are only practical at lower Reynolds numbers, and increasing the momentum injection can extend the practical uses of the technology. Here, we experimentally demonstrate improvement in the performance of a planar DBD actuator by utilizing an AC-augmented (ACA) electrical field in a three-electrode geometry. Time-resolved electrical and optical measurements, velocity profiles, and direct thrust measurements were used to characterize the EHD augmentation. Varying phase shift and E-field strength between the two air-exposed DBD electrodes can accelerate EHD flow and increase EHD forcing by up to ∼40%. At the most favorable conditions, the maximum thrust was 54 mN m−1 when the air-exposed electrodes were out of phase. In-phase operation of the exposed electrodes at high E-field conditions can induce adverse effects and sliding discharge. Mechanistically, the performance improvements in the ACA DBD actuator primarily come from the additional charge pull action by the ACA electrode. The insight into the ACA DBD mechanism allows for the development of multi-stage arrays capable of further increasing EHD forces.
17 March 2025 in Sensors and Actuators A: Physical
Aerosols dispersed and transmitted through the air (e.g., particulate matter pollution, bioaerosols) are ubiquitous and one of the leading causes of adverse health effects and disease transmission. A variety of sampling methods (e.g., filters, cyclones, impactors) have been developed to assess personal exposures. However, a gap still remains in the accessibility and ease-of-use of these technologies for people without experience or training in collecting airborne samples. Additionally, wet scrubbers (large non-portable industrial systems) utilize liquid sprays to remove aerosols from the air; the goal is to “scrub” (i.e., clean) the exhaust of industrial smokestacks, not collect the aerosols for analysis. Inspired by wet scrubbers, we developed a device fundamentally different from existing portable air samplers by using aerosolized microdroplets to capture aerosols in personal spaces (e.g., homes, offices, schools). Our aerosol-sampling device is the size of a small teapot, can be operated without specialized training, and features a winding flow path in a supersaturated relative humidity environment enabling droplet growth. The integrated open mesofluidic channels shuttle coalesced droplets to a collection chamber for subsequent sample analysis. Here, we present the experimental demonstration of aerosol capture into water droplets. Iterative study optimized the non-linear flow manipulating baffles and enabled an 83% retention of the aerosolized microdroplets in the confined volume of our device. As a proof-of-concept for aerosol capture into a liquid medium, 0.5-3 µm model particles were used to evaluate aerosol capture efficiency. Finally, we demonstrate the device can capture and keep a bioaerosol (bacteriophage MS2) viable for downstream analysis.