Haoze Ren

Haoze Ren

Auto-generated profile, based on publicly available information

Haoze Ren

Department of Chemical and Bimolecular Engineering, Lehigh University, Bethlehem, PA, 18015, USA

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 September 2024 in Chemistry of Materials
Verified
Journal Article
Open access
HRHaoze Ren
Haoze Ren
HLHan Li
Han Li
PBPatrick Barry
Patrick Barry
ZWZhongling Wang
Zhongling Wang
ACArmando Rodriguez Campos
Armando Rodriguez Campos
ERElsa Reichmanis
Elsa Reichmanis

13 February 2023 in Energy & Environmental Materials
Verified
Journal Article
Open access
HRHaoze Ren
Haoze Ren
YWYing Wang
Ying Wang
DCDaxian Cao
Daxian Cao
WGWilliam Gedney
William Gedney
TJTongtai Ji
Tongtai Ji
HZHongli Zhu
Hongli Zhu
Achieving high energy density and fast charging of lithium‐ion batteries can accelerate the promotion of electric vehicles. However, the increased mass loading causes poor charge transfer, impedes the electrochemical reaction kinetics, and limits the battery charging rate. Herein, this work demonstrated a novel pattern integrated stamping process for creating channels in the electrode, which benefits ion transport and increases the rate performance of the electrode. Meanwhile, the pressure applied during the stamping process improved the contact between electrode and current collector and also enhanced the mechanical stability of the electrode. Compared to the conventional bar‐coated electrode with the same thickness of 155 μm (delivered a discharge capacity of 16 mAh g−1 at the rate of 3 C), the stamped low‐tortuosity LiFePO4 electrode delivered 101 mAh g−1 capacity. Additionally, water was employed as a solvent in this study. Owing to its eco‐friendliness, high scalability, and minimal waste generation, this novel stamping technique inspire a new method for the industrial‐level efficient roll to roll fabrication of fast‐charge electrodes.

3 January 2024 in Chemical Communications
Verified
Journal Article
Closed access
PDF file
HRHaoze Ren
Haoze Ren
ETEsther S. Takeuchi
Esther S. Takeuchi
AMAmy C. Marschilok
Amy C. Marschilok
KTKenneth J. Takeuchi
Kenneth J. Takeuchi
ERElsa Reichmanis
Elsa Reichmanis
Propelled by the widespread adoption of portable electronic devices, electrochemical energy storage systems, particularly lithium-ion batteries (LIBs), have become ubiquitous in modern society.

28 August 2024 in ACS Applied Energy Materials
Verified
Journal Article
Open access
DGDonghee Gueon
Donghee Gueon
HRHaoze Ren
Haoze Ren
ZSZeyuan Sun
Zeyuan Sun
BLBar Mosevitzky Lis
Bar Mosevitzky Lis
DNDang D. Nguyen
Dang D. Nguyen
ERElsa Reichmanis
Elsa Reichmanis
Stress-relieving and electrically conductive single-walled carbon nanotubes (SWNTs) and conjugated polymer, poly[3-(potassium-4-butanoate)thiophene] (PPBT), wrapped silicon microparticles (Si MPs) have been developed as a composite active material to overcome technical challenges such as intrinsically low electrical conductivity, low initial Coulombic efficiency, and stress-induced fracture due to severe volume changes of Si-based anodes for lithium-ion batteries (LIBs). The PPBT/SWNT protective layer surrounding the surface of the microparticles physically limits volume changes and inhibits continuous solid electrolyte interphase (SEI) layer formation that leads to severe pulverization and capacity loss during cycling, thereby maintaining electrode integrity. PPBT/SWNT-coated Si MP anodes exhibited high initial Coulombic efficiency (85%) and stable capacity retention (0.027% decay per cycle) with a reversible capacity of 1894 mA h g-1 after 300 cycles at a current density of 2 A g-1, 3.3 times higher than pristine Si MP anodes. The stress relaxation and underlying mechanism associated with the incorporation of the PPBT/SWNT layer were interpreted by quasi-deterministic and quantitative stress analyses of SWNTs through in situ Raman spectroscopy. PPBT/SWNT@Si MP anodes can maintain reversible stress recovery and 45% less variation in tensile stress compared with SWNT@Si MP anodes during cycling. The results verify the benefits of stress relaxation via a protective capping layer and present an efficient strategy to achieve long cycle life for Si-based anodes for next-generation LIBs.

28 November 2024 in Chemical Communications
Verified
Journal Article
Closed access
PDF file
HLHan Li
Han Li
HRHaoze Ren
Haoze Ren
ZSZeyuan Sun
Zeyuan Sun
SQSiyu Qin
Siyu Qin
ACArmando Rodriguez Campos
Armando Rodriguez Campos
ERElsa Reichmanis
Elsa Reichmanis
Tailored side chains can improve structural stability, ion transport and capacity retention, offering a solution to key challenges such as capacity fade and electrode degradation in lithium-ion batteries.

21 March 2025 in Advanced Energy Materials
Verified
Journal Article
Open access
HRHaoze Ren
Haoze Ren
ZSZeyuan Sun
Zeyuan Sun
MWMeng Wang
Meng Wang
MSMengting Sun
Mengting Sun
HLHan Li
Han Li
ERElsa Reichmanis
Elsa Reichmanis
One focal area of contemporary organic mixed ionic‐electronic conductor (OMIEC) research relates to utilization of dual‐conductive properties to enhance the ion/electron transfer kinetics for energy storage applications. Insight regarding OMIEC response toward the electrolyte anion and solvent used in lithium‐ion batteries (LIBs), however, is limited. Here, for the first time, the solvent‐phobic and ionophilic (SP‐IP) properties of the OMIEC, poly[3‐(potassium‐4‐butanoate)thiophene‐2,5‐diyl] (P3KBT), are revealed through comprehensive evaluation and characterization. The solvent‐phobic characteristics arise from the cooperation of dispersive interaction, polar interaction, and hydrogen‐bonding between P3KBT and electrolyte solvent. The ionophilic nature is driven by electrostatic interactions between P3KBT side chain carboxylate groups and LiPF6, and the reversible electrochemical doping/de‐doping of the polythiophene backbone with PF6⁻. The SP‐IP properties induce formation of a LiF‐rich, Li2CO3‐limited cathode electrolyte interphase (CEI) layer when a P3KBT coating layer is applied to the active material surface, significantly improving half‐cell life to over 1500 cycles at 2C.