Nacim Ramdani

Nacim Ramdani

Auto-generated profile, based on publicly available information

Nacim Ramdani

Laboratoire pluridisciplinaire de recherche en ingénierie des systèmes, mécanique et énergétique

Research Focus & Metrics

Academic Career Length

30Years (1997-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2004 in Automatica
Verified
Journal Article
Closed access
TRT. Raı̈ssi
T. Raı̈ssi
NRN. Ramdani
N. Ramdani
YCY. Candau
Y. Candau

22 September 2009 in IEEE Transactions on Automatic Control
Verified
Journal Article
Closed access
NRNacim Ramdani
Nacim Ramdani
NMNacim Meslem
Nacim Meslem
YCYves Candau
Yves Candau
In this paper, we show how to compute an over-approximation for the reachable set of uncertain nonlinear continuous dynamical systems by using guaranteed set integration. We introduce two ways to do so. The first one is a full interval method which handles whole domains for set computation and relies on state-of-the-art validated numerical integration methods. The second one relies on comparison theorems for differential inequalities in order to bracket the uncertain dynamics between two dynamical systems where there is no uncertainty. Since the derived bracketing systems are piecewise Ck-differentiable functions, validated numerical integration methods cannot be used directly. Hence, our contribution resides in the use of hybrid automata to model the bounding systems. We give a rule for building these automata and we show how to run them and address mode switching in a guaranteed way in order to compute the over approximation for the reachable set. The computational cost of our method is also analyzed and shown to be smaller that the one of classical interval techniques. Sufficient conditions are given which ensure the epsiv-practical stability of the enclosures given by our hybrid bounding method. Two examples are also given which show that the performance of our method is very promising.

1 May 2011 in Nonlinear Analysis: Hybrid Systems
Verified
Journal Article
Closed access
NRNacim Ramdani
Nacim Ramdani
NNNedialko S. Nedialkov
Nedialko S. Nedialkov

1 August 2005 in Journal of Process Control
Verified
Journal Article
Closed access
TRT. Raïssi
T. Raïssi
NRN. Ramdani
N. Ramdani
YCY. Candau
Y. Candau

10 December 2015 in IEEE Sensors Journal
Verified
Journal Article
Closed access
VBVincent Bonnet
Vincent Bonnet
VJVladimir Joukov
Vladimir Joukov
DKDana Kulic
Dana Kulic
PFPhilippe Fraisse
Philippe Fraisse
NRNacim Ramdani
Nacim Ramdani
GVGentiane Venture
Gentiane Venture
This paper investigated the possibility of estimating 3D lower limb joint kinematics during five popular rehabilitation exercises of the hip and knee joints based on the data collected from a single inertial measurement unit located on the shank. The leg was modeled as a four-degree-of-freedom serial chain, and the relevant joint angles were represented by Fourier series. A least square approach based on the minimization of the difference between the measured and estimated 3D linear accelerations and angular velocities was used to solve the related analytical problem. The approach was validated on ten healthy young volunteers (ten trials each), comparing the proposed approach with the measurements collected through a stereophotogrammetric system. The average root mean square differences between the estimated joint angles and those reconstructed with the stereophotogrammetric system were inferior than 3.2° with correlation coefficients higher than 0.85.

1 May 2010 in Nonlinear Analysis: Hybrid Systems
Verified
Journal Article
Closed access
NRNacim Ramdani
Nacim Ramdani
NMNacim Meslem
Nacim Meslem
YCYves Candau
Yves Candau