30 June 2023 in Technobius
The increase in the construction of asphalt concrete roads in Kazakhstan has led to the development of research on raw materials in this industry. Bitumen binder as the main component affecting the deformation properties, as well as the physical and mechanical properties of coatings, in general, is of the greatest interest to builders. The analysis of scientific sources in the field of the application of various modifiers of bitumen binders is carried out. Polymer-based additives have been widely used in road construction. The use of half-dimensional additives contributes to the improvement of asphalt concrete indicators: strength properties, water resistance, deformative stability of the coating at high and low operating temperatures, wear resistance, and resistance to rutting, which generally increases the repair time and contributes to a corresponding reduction in operating costs. This article presents a study of the properties of bitumen modified with an additive based on rubber crumbs. Indicators such as penetration depth and softening temperature by the ring and ball method are investigated in the article. The samples with different content of additives were taken: control sample without additives, and samples with the addition of modifiers in the amount of 5%, 10%, 12%, and 15% out of bitumen weight. The highest viscosity is shown by the sample with a modifier of 12%. Bitumen samples with a modifier content of 12% and 15% correspond to the standard indicators regarding softening temperature.
30 December 2022 in Technobius
The main purpose of the examination of roads is the timely identification of areas that require improvement of road conditions, as well as the evaluation of the state of all structural elements of roads. The study of the causes of road deformations, measures to eliminate and prevent warping are the main issue of road maintenance. The survey of roads was conducted in accordance with the approved methods using standard measuring tools. PLAXIS software was used to perform the finite element analysis of deformations and stability of soil, to calculate the interaction of the pavement with the ground, the effect of heat fluxes. Processing of data on the road Almaty-Taraz has shown that stresses and deformations arise directly in the place of contact of point loads with trapezoidal shape on the depth of influence. The authors conclude that when horizontal deformations occur, the greatest stresses occur on the road shoulders, which surrounds possible slope collapses. In addition, volumetric deformations of the foundation occur under direct dynamic loading and, under its prolonged effect, contribute to the appearance of volumetric bulging deformations.
30 September 2026 in Bulletin of Kazakh Leading Academy of Architecture and Construction
The aim of this study was to evaluate the effects of isotactic polypropylene H-350 and sunflower foots (SF) on the empirical physical properties and short-term aging behavior of BND 100/130 road bitumen. The scientific novelty consists in the systematic experimental assessment of a locally sourced BND 100/130-PP H-350-SF system with simultaneous variation of PP and SF contents and blending technique, including evaluation of apparent phase heterogeneity and RTFOT behavior. Eleven formulations were prepared with 3–5 wt.% PP H-350 and 0-4 wt.% SF. Penetration at 25 °C, ring-and-ball softening point, and ductility were determined, while short-term aging of three formulations was evaluated using RTFOT. Penetration ranged from 31.4 to 76.4 × 0.1 mm, and softening point from 53.0 to 67.2 °C; phase-separated formulations showed paired values. RTFOT mass loss was 0.04-0.10%. For phase-matched samples, penetration retention was approximately 97.9% and 94.6% for the two reported phases of Mix 7 and 104.2% for Mix 9. An asphalt concrete test mixture prepared with a reported PP-modified binder showed water absorption of 2.95 vol.%, cohesion of 0.27 MPa, tensile crack resistance of 3.4 MPa at -10 °C, and compressive strengths of 3.1 MPa at 20 °C and 1.1 MPa at 50 °C. The results support empirical comparison of the formulations but do not establish EN 14023 compliance or Superpave Performance Grade. Further rheological, storage-stability, mixture-design, and statistical studies are required for definitive performance classification.