30 November 2023 in IEEE Journal of Solid-State Circuits
This article presents a four-way hybrid parallel–series Doherty power amplifier (PA) architecture that supports broadband operation and deep power back-off (PBO) efficiency enhancement for next-generation wireless communication. Most existing load modulation PAs are limited in bandwidth due to the large impedance transformation ratios (ITRs) needed for load-pull matching at deep PBO. The proposed technique achieves wide carrier bandwidth by exploiting different frequency-dependent active load modulations of the parallel/series Doherty combiners and PA path biasing reconfiguration, while the deep PBO efficiency enhancement is realized by the optimum turn-on sequences of the four PA paths. The behavior of the implemented PA load modulation network is mathematically described at different PBO levels corresponding to the output power levels at which each efficiency enhancement occurs. As a proof-of-concept design, a 26–40-GHz PA is implemented in the GlobalFoundries 45-nm CMOS SOI process. The PA measures 22.5–23.9-dBm OP textsubscript 1dB, 26.2%–38.2% PAE textsubscript OP1dB, 18.1%–34.5% PAE textsubscript 6dB PBO, and 10.7%–22.1% PAE textsubscript 12dB PBO. Note that the PBO levels are referenced from OP textsubscript 1dB. Compared to a normalized ideal class-B PA, this design achieves 1.3–1.8 $\times $ power-added efficiency (PAE) boost at 6-dB PBO and 1.6–2.3 $\times $ boost at 12-dB PBO. With a 100-MHz fifth-generation (5G) new radio (NR) frequency range 2 (FR2) 1-CC 64-QAM signal, this PA achieves 9.26–16.9-dBm average output power and 9.9%–25.5% average PAE at an rms error vector magnitude (EVM) of -25 dB for 26–40 GHz. With a 1-CC 400-MHz 16-QAM signal, the PA achieves 12.95–17.4-dBm average output power and 12.5%–27% average PAE at an rms EVM of -20 dB for 26–40 GHz.
25 January 2023 in IEEE Journal of Solid-State Circuits
The vast available spectrum at millimeter-wave (mm-Wave)/terahertz (THz) frequencies is envisioned as a key enabler to solve the ever-increasing data rate needs in crowded urban environments and lead the next wireless technology revolution. To overcome the high path loss present at mm-Wave/THz, highly directional antenna arrays have become ubiquitous. Their future large-scale deployment will naturally create dense wireless sensor networks, which in-turn enable joint communication and sensing. However, the beamforming of high-directivity antenna arrays relies on real-time precise localization between transmitters (TXs) and receivers (RXs) to ensure robustness in dynamic mobile applications. Moreover, traditional digital encryption and decryption at multi-Gbps data rate cause large power and latency overhead, and thus, wireless physical layer security has become a promising solution. In this article, we propose and demonstrate a reconfigurable phase-time array (PTA) TX with prism-like spectral-to-spatial mapping of wideband transmitted signals, which achieves keyless physically secured wireless communication and fast multi-RX localization to enable low-latency joint communication and sensing within the same wireless electronics frontend. The PTA realizes reconfigurable spectral-to-spatial mapping by applying both a phase shift and true time delay (TTD) at each array element. This intentionally creates and exploits the array beam squinting effect, such that different frequency components of a wideband signal are transmitted in different directions, analogous to an optical prism. Therefore, multiple RX nodes can simultaneously determine their angular positions relative to the TX array using their received signals for fast multi-RX localization. Judiciously engineering the prism-like beam squinting in PTA TX can also selectively distort signal transmission to unwanted directions for secured communication without cryptography. Furthermore, the PTA scheme can reconfigure its element-level phase-time delay combinations to attain variable levels of communication security and localization/sensing performance depending on the needs.
4 February 2025 in IEEE Journal of Solid-State Circuits
This article describes a three-way power amplifier (PA) topology that achieves broadband power back-off (PBO) efficiency enhancement without using active load modulation on the Main PA or supply modulation. This allows the PA to avoid the classic trade-off between load modulation and bandwidth that is typical among Doherty PAs. Unlike Doherty PAs, the proposed PA has both its voltage and current drive profiles reach a maximum at PBO, which causes the impedance of the Main PA to be constant across the entire input drive. This is achieved with a novel parallel-series output matching network (OMN) that primarily utilizes coupled-line baluns. A prototype is fabricated in the GlobalFoundries 45 nm RFSOI and achieves a $P_{\text {avg}}$ and $\mathrm {PAE_{avg}}$ of 6.45–12.61 dBm and 5.9%–16.4% from 25 to 40 GHz, respectively. With a 200 MHz signal, $P_{\text {avg}}$ and $\mathrm {PAE_{avg}}$ are 5.58–11.1 dBm and 4.8%–13.3%, respectively.
10 January 2025 in IEEE Journal of Solid-State Circuits
The output power of a transmitter (TX) array can degrade due to a variety of factors, such as device aging, thermal degradation, and load impedance mismatch of the power amplifier due to antenna mutual coupling. Power sensors are needed on phased arrays to detect if any output power degradation occurs. Of these events, we will mainly focus on antenna voltage standing wave ratio (VSWR)-related power degradation, as these events occur on a much shorter timescale compared with long-term effects such as device aging. VSWR-resilient power sensors are required to support these VSWR scenarios. They need to maintain high sensing accuracy and dynamic range (DR) even under unknown complex load impedances in a compact form factor. Therefore, this work presents a broadband VSWR-resilient compact power and gain sensor with integrated power amplifier (PA) that achieves a power sensing error (PSE) of ≤±1.5/3 dB over a VSWR of 2:1/3:1, respectively, from 27 to 39 GHz. Over the same 2:1/3:1 VSWR and frequency range, the DR is >18.69/17.65 dB. The sensor consumes 24.8 mW of power and occupies only 0.044 mm2, ensuring a low overhead implementation for array applications. The sensor is also PA design-agnostic and supports single-ended antennas.
4 November 2025 in IEEE Journal of Solid-State Circuits
Doherty power amplifiers (DPAs) use active load modulation to increase efficiency at power back-off, a process that requires at least two power amplifier (PA) paths. Typically, this results in a much larger area compared to single-path PAs, which hinders their integration into complex transceiver systems, such as large-scale high-density phased arrays. This article presents a circuit topology for reducing the size of a DPA output matching network (OMN) to that of a single transformer, thereby achieving a DPA size at least as compact as a single-path PA. This network achieves impedance inverting and scaling functionalities, which are critical for any Doherty OMN, through the use of a three-coil transformer. At 28 GHz, this PA achieves an $\mathrm {\text {OP}_{\text {1 dB}}}$ of 20.4 dBm, and 38% PAE at $\mathrm {\text {OP}_{\text {1 dB}}}$ . At a power back-off of 6 and 9 dB, the PA achieves a PAE of 29.3% and 20.3%, respectively. With a 100 MHz 5G NR FR2 OFDM 64-/256-QAM signal, this PA achieves $\mathrm {P}_{\text {AVG}}$ of 12.05/9.8 dBm and $\mathrm {\text {PAE}_{\text {AVG}}}$ of 21.0%/15.1%. With a 200 MHz 64-/256-QAM signal, $P_{\text {AVG}}$ is 11.08/8.4 dBm and $\mathrm {\text {PAE}_{\text {AVG}}}$ is 18.4%/12.8%. The core area is 0.154 mm2, which is among the smallest reported compared to other DPAs with a similar center frequency and output power level.