Wireless power technology offers the promise of cutting the last cord, allowing users to seamlessly recharge mobile devices as easily as data are transmitted through the air. Initial work on the use of magnetically coupled resonators for this purpose has shown promising results. We present new analysis that yields critical insight into the design of practical systems, including the introduction of key figures of merit that can be used to compare systems with vastly different geometries and operating conditions. A circuit model is presented along with a derivation of key system concepts, such as frequency splitting, the maximum operating distance (critical coupling), and the behavior of the system as it becomes undercoupled. This theoretical model is validated against measured data and shows an excellent average coefficient of determination of 0.9875. An adaptive frequency tuning technique is demonstrated, which compensates for efficiency variations encountered when the transmitter-to-receiver distance and/or orientation are varied. The method demonstrated in this paper allows a fixed-load receiver to be moved to nearly any position and/or orientation within the range of the transmitter and still achieve a near-constant efficiency of over 70% for a range of 0-70 cm.
6 June 2008 in IEEE Transactions on Instrumentation and Measurement
This paper presents the wireless identification and sensing platform (WISP), which is a programmable battery-free sensing and computational platform designed to explore sensor-enhanced radio frequency identification (RFID) applications. WISP uses a 16-bit ultralow-power microcontroller to perform sensing and computation while exclusively operating from harvested RF energy. Sensors that have successfully been integrated into the WISP platform to date include temperature, ambient light, rectified voltage, and orientation. The microcontroller encodes measurements into an electronic product code (EPC) Class 1 Generation 1 compliant ID and dynamically computes the required 16-bit cyclical redundancy checking (CRC). Finally, WISP emulates the EPC protocol to communicate the ID to the RFID reader. To the authors' knowledge, WISP is the first fully programmable computing platform that can operate using power transmitted from a long-range (UHF) RFID reader and communicate arbitrary multibit data in a single response packet.
This paper describes two wireless power transfer systems. The Wireless Identification and Sensing Platform (WISP) is a platform for sensing and computation that is powered and read by a commercial off-the-shelf UHF (915 MHz) RFID reader. WISPs are small sensor devices that consume on the order of 2 uW to 2 mW, and can be operated at distances of up to several meters from the reader. The second system harvests VHF or UHF energy from TV towers, with power available depending on range and broadcast transmit power. We report on an experiment in which 60 uW is harvested at a range of about 4 km.
Effective means of delivering wireless power to volumes of spaces will enable users the freedom and mobility to seamlessly power and recharge their devices in an unencumbered fashion. This has particular importance for consumer electronic, medical, and industrial applications, where usage models focus on unstructured and dynamic environments. However, existing wireless power technology falls short of this vision. Inductive charging solutions are limited to near-contact distances and require a docking station or precise placement for effective operation. Far-field wireless power techniques allow much greater range, but require complicated tracking systems to maintain a line-of-sight connection for high-efficiency power delivery to mobile applications. Recent work using magnetically coupled resonators (MCRs) for wireless power delivery has shown a promising intersection between range (on the order of a meter), efficiency (over 80%), and delivered power (up to tens of watts). However, unpredictable loads rapidly change system operating points, and changes in position disrupt system efficiency, which affects the ultimate usability of these systems. Dynamic adaptation to these changes in operating conditions and power transfer range is a critical capability in developing a fully functional and versatile wireless power solution. This paper provides an overview of methods used to adapt to variations in range, orientation, and load using both wideband and fixed-frequency techniques.
This paper presents a wireless, battery-free, platform for sensing and computation that is powered and read by a standards compliant ultra-high frequency (UHF) radio frequency identification (RFID) reader. The WISP (wireless identification and sensing platform) includes a fully-programmable 16 bit microcontroller with analog-to-digital converter. The microcontroller firmware implements portions of the electronic product code (EPC) class 1 generation 1 protocol. When queried, the platform communicates arbitrary sensor data by emulating an EPC tag whose ID encodes the desired sensor data; the required 16-bit CRC is computed dynamically by the microcontroller. The RFID reader reports the received tag ID to application software which can interpret the information contained in the tag ID. The programmability of the WISP along with its implementation as a PCB allows for flexible integration of arbitrary low-power sensors. Furthermore, sensors are also exclusively powered from the RFID reader resulting in a completely battery free device. Sensors integrated into the WISP platform so far include light, temperature, and rectified voltage, and are shown experimentally to have an operating range of up to 4.5m. To the authors' knowledge, WISP is the first fully programmable computing platform that can operate using power transmitted from a long-range (UHF) RFID reader and communicate arbitrary, multi-bit data in a single response packet.