25 March 2023 in Drvna industrija
This study presents opportunities for the utilization of timber by-products with defects for manufacturing engineered wood panels. Three gluing methods were proposed for this waste raw material derived from Scots pine (Pinus sylvestris L.) wood. The methods used for combining and gluing enabled a more complete and complex utilization of wood with defects. The physical properties (density and moisture content) and mechanical properties (bending strength and modulus of elasticity) of the laboratory-fabricated engineered wood panels were evaluated in accordance with the European standards. The highest density of 643 kg/m3 and bending strength values (28.6 N/mm2) were obtained from the panels manufactured using method 3 and veneered with beech veneer sheets. The modulus of elasticity of the laboratory-made engineered wood panels reached values of up to 5580 N/mm2. This study demonstrated the feasibility of the utilization of defective wood pieces in the manufacturing of engineered wood panels.
20 June 2020 in European Mechanical Science
This study presents the results of investigations on some physical and mechanical properties of one-layer particleboards made from Scots pine (Pinus sylvestris L.). The size and the ratio of the using particles were: 0.5-1 mm- 20 %, 1-3 mm- 60 % and 3-5 mm-20 %, respectively. Urea-formaldehyde resin was used as a binder. The effect of different pressing time- 15, 30, 60 and 90 s . mm-1 on the some properties, such as: density, moisture content, water absorption, thickness swelling and bending strength according to appropriate standards was evaluated. The best results were observed at pressing time of 60 and 90 s . mm-1. The particleboards obtained under these conditions can be used in the furniture industry .
1 November 2021 in Maderas. Ciencia y Tecnología
This study presents an opportunity for rational utilization of poplar wood peeler cores in the production of glued laminated timber (glulam) beams. An approach for optimal use of small-diameter raw material with a circular cross-section is also proposed in order to obtain a final product in a significantly high quantitative yield. The applied novel method of sawing the peeler cores and subsequent combination of gluing the obtained lamellas allows to achieve: reduction of labor and energy consumption in the processing; rational utilization of this waste raw material; obtaining a product sought by consumers; opportunity to implement technology for the production of glulam from peeler cores. The results showed that sawing the peeler cores and obtaining lamellas with a trapezoidal cross-section leads to a high quantitative yield of 76,3 %. The final quantitative yield in subsequent technological operations in the manufacturing of engineered wood of glulam type reaches 48,8 % of the volume of raw material. In addition, equations have been working are used for the determination of the most suitable sizes of the lamellas, depending on the diameter and the kerf width.
18 September 2025 in Drvna industrija
Adhesives used in the production of wood composite materials, including engineered wood, are a significant component that characterizes the performance of the final products. Also, the adhesive type, quantity and properties significantly impact the cost of the resulting materials. The aim of this review was to present some of the basic characteristics of bonding agents for engineered wood. Based on the information provided, a suitable adhesive can be selected to form final products that meet the needs of consumers. Therefore, it is of essential importance to know the advantages and disadvantages of adhesives, since global trends require the creation of environmentally friendly products. The latter must contain a minimum amount of free formaldehyde. The object of this review was to deliver an analysis of the most commonly used synthetic resins in the production of engineered wood products (EWPs), namely amino based, phenolic based, isocyanate, polyurethane and polyvinyl acetate.
24 January 2024 in Wood Material Science & Engineering
30 December 2024 in Drvna industrija
The present study examines the bonding strength of five-layer plywood made from beech wood (Fagus sylvatica L.). An alcohol-soluble phenol-formaldehyde (PF) resin as an adhesive between the veneer sheets was used. Various pressing factors, showing the effect of the varying ratio between them, were applied. The experimental samples both in a dry state and after immersion in boiling water for one hour were tested. The results clearly demonstrated that the bonding strength is very high when using the alcohol-soluble PF resin and meets the requirements of the standard BDS EN 314-2: 2002. The best bonding strength values were obtained at a presstemperature of 145 °C, adhesive spread of 150 to 170 g/m2, and initial adhesive temperature of 30-40 °C.