Еlena А. Sklyarova

Еlena А. Sklyarova

Auto-generated profile, based on publicly available information

Еlena А. Sklyarova

National Research Tomsk Polytechnic University

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2015 in Journal of Quantitative Spectroscopy and Radiative Transfer
Verified
Journal Article
Closed access
OUO.N. Ulenikov
O.N. Ulenikov
OGO.V. Gromova
O.V. Gromova
EBE.S. Bekhtereva
E.S. Bekhtereva
KBK.B. Berezkin
K.B. Berezkin
ESE.A. Sklyarova
E.A. Sklyarova
SBS. Bauerecker
S. Bauerecker

21 June 2019 in Metals
Verified
Journal Article
Open access
PDF file
Alexey PaninAlexey Panin
Alexey Panin
MKMarina Kazachenok
Marina Kazachenok
OPOlga Perevalova
Olga Perevalova
SMSergey Martynov
Sergey Martynov
APAlexandra Panina
Alexandra Panina
ESElena Sklyarova
Elena Sklyarova
In the present study, the methods of optical, scanning electron, and transmission electron microscopy as well as X-ray diffraction analysis gained insights into the mechanisms of surface finish and microstructure formation of Ti–6Al–4V parts during an EBF3-process. It was found that the slip band propagation within the outermost surface layer provided dissipation of the stored strain energy associated with martensitic transformations. The latter caused the lath fragmentation as well as precipitation of nanosized β grains and an orthorhombic martensite α″ phase at the secondary α lath boundaries of as-built Ti–6Al–4V parts. The effect of continuous electron beam post-treatment on the surface finish, microstructure, and mechanical properties of EBF3-fabricated Ti–6Al–4V parts was revealed. The brittle outermost surface layer of the EBF3-fabricated samples was melted upon the treatment, resulting in the formation of equiaxial prior β grains of 20 to 30 μm in size with the fragmented acicular α′ phase. Electron-beam irradiation induced transformations within the 70 μm thick molten surface layer and 500 μm thick heat affected zone significantly increased the Vickers microhardness and tensile strength of the EBF3-fabricated Ti–6Al–4V samples.

30 October 2021 in Metals
Verified
Journal Article
Open access
PDF file
Alexey PaninAlexey Panin
Alexey Panin
SMSergey Martynov
Sergey Martynov
MKMarina Kazachenok
Marina Kazachenok
LKLyudmila Kazantseva
Lyudmila Kazantseva
ABAlexander Bakulin
Alexander Bakulin
ESElena Sklyarova
Elena Sklyarova
The inferior mechanical properties of EBAM Ti-6Al-4V samples are due to the coarse columnar grains containing coarse lamellar structures. One can expect that water cooling of the build platform will increase the cooling rate of the molten pool during the build-up process, causing microstructure refinement. In the present work, the substrate cooling effects on the microstructure and phase composition of EBAM Ti-6Al-4V samples are studied using optical, scanning electron, and scanning transmission microscopy, as well as X-ray diffraction analysis. It is shown that the microstructure of the EBAM Ti-6Al-4V samples built on the substrate without water cooling consists predominantly of columnar prior β grains with lateral sizes ranging up to 2000 µm, while cooling of the build platform causes the appearance of equiaxed prior β grains measuring 1000 µm. Moreover, the refinement of the martensite structure and the precipitation of α′′ martensite platelets within α laths occur in the EBAM Ti-6Al-4V samples built on the water-cooled build platform. An explanation of the mechanisms underlying the α′→α + β and α′→α + α′′ + β transformations during the building process is provided based upon ab initio calculations. The fragmentation of the α laths under the residual compressive stresses is discussed.

1 December 2015 in Journal of Molecular Spectroscopy
Verified
Journal Article
Closed access
OUO.N. Ulenikov
O.N. Ulenikov
OGO.V. Gromova
O.V. Gromova
EBE.S. Bekhtereva
E.S. Bekhtereva
YKYu.V. Krivchikova
Yu.V. Krivchikova
ESE.A. Sklyarova
E.A. Sklyarova
SBS. Bauerecker
S. Bauerecker

1 December 2016 in Journal of Quantitative Spectroscopy and Radiative Transfer
Verified
Journal Article
Closed access
OUO.N. Ulenikov
O.N. Ulenikov
EBE.S. Bekhtereva
E.S. Bekhtereva
OGO.V. Gromova
O.V. Gromova
VZV.A. Zamotaeva
V.A. Zamotaeva
ESE.A. Sklyarova
E.A. Sklyarova
SBS. Bauerecker
S. Bauerecker

30 March 2021 in Metals
Verified
Journal Article
Open access
PDF file
Alexey PaninAlexey Panin
Alexey Panin
Andrey DmitrievAndrey Dmitriev
Andrey Dmitriev
ANAnton Yu. Nikonov
Anton Yu. Nikonov
MKMarina Kazachenok
Marina Kazachenok
OPOlga Perevalova
Olga Perevalova
ESElena Sklyarova
Elena Sklyarova
Experimental and theoretical studies helped to reveal patterns of surface roughening and the microstructure refinement in the surface layer of commercial pure titanium during ultrasonic impact treatment. Applying transmission electron microscopy technique, a gradient microstructure in the surface layer of the ultrasonically treated sample, where the grain size is varied from nano- to micrometers was revealed. It was shown that the surface plastic strains of the titanium sample proceeded according to the plastic ploughing mechanism, which was accompanied by dislocation sliding, twinning, and the transformations of the microstructure and phase composition. The molecular dynamics method was applied to demonstrate the mechanism of the phase transformations associated with the formation of stacking faults, as well as the reversible displacement of atoms from their sites in the hcp lattice, causing a change in coordination numbers. The role of the electronic subsystem in the development of the strain-induced phase transformations during ultrasonic impact treatment was discussed.