Controlling fluid flow is a fundamental problem with applications from biomedicine to environmental engineering. Contemporary solutions combine electromechanical sensors, valves, and pumps; however, these are expensive and difficult to maintain. We report an autonomous flow control principle inspired by vascular transport in plants. Combining experiments on real and biomimetic tissues, we show that networks of cells linked by nonlinear valves permit the physical programming of a nearly arbitrary pressure drop versus flow rate relation. The nonlinearity is a consequence of fluid-structure interactions that allow a flexible element to selectively block the valve aperture. We report four applications: parallel connections that function as (i) a nonlinear flow controller, (ii) a constant flow controller, (iii) a reverse Ohm flow controller, and a serial connection that acts as (iv) a fluidic on-off switch.
Pulsating flows are common in many industrial, scientific, and natural fluidic systems. However, because the oscillatory flow component disturbs, e.g., optical measurements, deposition, or industrial processes, it is rarely desired. Moreover, in physiological conditions, pulsation control is desired. We explore the effect of using a plant-inspired nonlinear resistor to smooth the output of a peristaltic pump. Incorporating a 3D printed millifluidic biomimetic device reduces the oscillation amplitudes by 3 orders of magnitude, from to of the output flow rate. This represents a tenfold improvement relative to a purely linear resistive-capacitive approach. The observed flow kinetics compare well to a predictive model of peristaltic transport, allowing the further development of optimized fluid-handling systems driven by pulsatile flow. Applications to particle tracking and jetting are considered.
Summary: Formation of an aqueous continuum from the leaf surface to the sub‐stomatal cavity is a key process, affecting the foliar entry of solutes, particles, and pathogens. However, the factors controlling the transition from a water droplet to the formation of a continuous water film remain poorly understood. To address current limitations in state‐of‐the‐art bioimaging methods, we developed an X‐ray micro‐CT technique that enables nondestructive, time‐resolved visualization of water films on live barley (Hordeum vulgare) and potato (Solanum tuberosum) plants under controlled environmental conditions. We compare droplet behavior, leaf wetting, and the formation of foliar water films on two important crop plants, potato and barley, which differ markedly in their leaf surface characteristics, in terms of hydrophobicity of the cuticle, as well as stomatal topography and trichome morphology and density. We show that continuous water films, from the cuticle into stomata, may form within a few hours, and that a given set of environmental conditions may trigger hydraulic activation of stomata in one crop but not in another, depending largely on the physicochemical properties of the liquid and leaf surface morphological features.
The electric-field-induced and temperature induced dynamics of domains, defects, and phases play an important role in determining the macroscopic functional response of ferroelectric and piezoelectric materials. However, distinguishing and quantifying these phenomena remains a persistent challenge that inhibits our understanding of the fundamental structure–property relationships. In situ dark field x-ray microscopy is a new experimental technique for the real space mapping of lattice strain and orientation in bulk materials. In this paper, we describe an apparatus and methodology for conducting in situ studies of thermally and electrically induced structural dynamics and demonstrate their use on ferroelectric BaTiO3 single crystals. The stable temperature and electric field apparatus enables simultaneous control of electric fields up to ≈2 kV/mm at temperatures up to 200 °C with a stability of ΔT = ±0.01 K and a ramp rate of up to 0.5 K/min. This capability facilitates studies of critical phenomena, such as phase transitions, which we observe via the microstructural change occurring during the electric-field-induced cubic to tetragonal phase transition in BaTiO3 at its Curie temperature. With such systematic control, we show how the growth of the polar phase front and its associated ferroelastic domains fall along unexpected directions and, after several cycles of electric field application, result in a non-reversible lattice strain at the electrode–crystal interface. These capabilities pave the way for new insights into the temperature and electric field dependent electromechanical transitions and the critical influence of subtle defects and interfaces.
Many applications require monitoring of increasingly high neutron flux levels. Pre‐neutron characterization is performed of a superconducting transition edge bolometric device, sensitive to neutrons by an enriched boron carbide (10B4C) layer. Heat from the absorption of neutrons is simulated using an attenuated laser, while the detector is cooled to the critical temperature, Tc. Frequency dependent (4–25 Hz) and constant input power measurements are performed on a 10B4C‐coated and a non‐coated pixel. Results are used to fit a two lumped element thermal model. The effective specific heat is highly dependent on the input pulse duration due to the interconnected stack structure. For modulated pulses, the active volume in the thermal circuit is the full depth of the substrate in the area under the pixel. For constant power input, a large portion of the substrate is heated and the interface conductivities to the cold finger are found to be important. The detectivity is D* = 3.5 × 108 , and is only slightly lower than similar detectors. Understanding the dynamics of the detector better and using neutron excitation, it is expected that optimizations can lead to an equally good detector for cold to thermal neutrons at flux levels >106 n cm−2s−1.