The objective of this study was to evaluate the compatibility degrees among primary sawing residues of eight different hardwoods from Amazonia and Portland cement type II-Z and correlate them with their chemical composition. The compatibility degree was expressed using the Inhibitory Index and the chemical characteristics were obtained by quantitative methods of extraction and analytical pyrolysis. From the species studied, five of them were classified as low inhibitory: Eschweilera coriacea, Inga paraensis, Inga alba, Pouteria guianensis, and Byrsonima crispa. There was no significant correlation between polar or non-polar soluble extractives and cement set inhibition. However, the Swartzia recurva samples with arabinose content were directly correlated with the cement inhibition. This effect also occurs with Larix because the alkali solution of the reaction cleaves the linkage between lignin and hemicellulose/cellulose and produces higher amounts of degraded polysaccharides which are responsible for the inhibition.
Este trabalho teve como objetivo avaliar dois modelos de desdobro (radial e tangencial) de madeira de Eucalyptus cloeziana e Eucalyptus saligna, numa serraria portátil, para se eleger o qual proporciona maior rendimento em madeira serrada. Para o estudo, foram selecionadas aleatoriamente 24 árvores com 27 anos de idade, sendo 12 árvores de cada espécie e divididas em duas classes diamétricas: 30-34,5 cm e 35-39,5 cm. As árvores foram derrubadas e traçadas em toras de 3,4 m de comprimento, sendo produzidas tábuas de 25 mm de espessura nominal. Os resultados obtidos demostraram que, para as duas classes diamétricas de espécies, o modelo de desdobro tangencial obteve melhor desempenho em relação ao desdobro radial, em termos de rendimento. Pode-se concluir-se que o Eucalyptus cloeziana obteve melhores rendimentos, com maior destaque para o modelo de desdobro tangecial em relação ao modelo radial. Estas espécies, nas condições estudadas, têm potencial para ser uma fonte alternativa e segura para produção de madeira serrada, substituindo algumas espécies nativas, ora sob pressão, em Moçambique.
24 November 2015 in Revista de Ciências Agroveterinárias
The aim of this study was to evaluate the performance of the messassa wood Brachystegia spiciformis and Julbernardia globiflora for three types of finishing products for use in the furniture and frames industries. Coating performance was assessed by adhesion strength, impact deformation resistance, abrasiveness, gloss and overall color variation tests based on technical standards. Copal painting application was higher for gloss, adhesion and lower abrasiveness compared to water based and polyurethane. The impact deformation was higher for polyurethane than water-based and copal for both species. The darkening of wood for Brachystegia spiciformis and a slight lightening of wood by Julbernardia globiflora characterize the overall color variation after application of the coating products. According to these results, the varnishes can be used to add value to the messassa wood as a finish in solid wood furniture and frames.
Wood trade is strongly dependent on global economic conditions. In Africa, the market for tropical wood also has dynamic changes. In Mozambique, the international demand for wood comes mainly from emerging economies such as China and India. Almost 70 % of the country is still covered by forests and other woody vegetation. There are many species with favorable properties for wood commerce, although, at present, this is restricted to a few species. We analyzed the wood anatomy of Acacia nigrescens, Combretum imberbe, Icuria dunensis, Pericopsis angolensis and Sterculia appendiculata and comment about properties and potential use based on their anatomical composition. In general, the species presented wood diffuse pores, simple perforation plates, alternate intervessel pits, deposits in vessels; abundant axial parenchyma; multiseriate rays, very thick-walled fibers and mineral inclusions. Based on anatomical characteristics, the studied species have great potential for use in panels industry, furniture, floor, structures and craftwork.
Wood plays a fundamental role in mitigating climate change due to its ability to fix and store carbon dioxide (CO₂). This study estimated the carbon stored in wood products at Eduardo Mondlane Secondary School in Maputo, Mozambique. Simple random sampling was adopted in five classrooms, measuring the dimensions and humidity of furniture (desks, doors, windows, blackboards, tables, and chairs) to calculate volumes, apparent densities, and CO₂ stocks, according to the EN 16449:2014 standard. The results revealed that mixed desks (wood and metal, type 1) store an average of 308.56 kg of CO₂ each, while solid wood desks (type 2) accumulate 511.08 kg. Doors stand out with 1,834.68 kg of CO₂ per unit, compared to 23.54 kg in blackboards. In the real-world school setting, the total carbon stock reaches 244,091 kg of CO2, equivalent to 290.58 kg/m² (considering 56 m² per classroom). It is concluded that wood products in public schools represent a significant carbon reservoir, contributing to climate mitigation.