The limited access to fast and facile general analytical methods for cellulosic and/or biocomposite materials currently stands as one of the main barriers for the progress of these disciplines. To that end, a diverse set of narrow analytical techniques are typically employed that often are time-consuming, costly, and/or not necessarily available on a daily basis for practitioners. Herein, we rigorously demonstrate a general quantitative NMR spectroscopic method for structural determination of crystalline cellulose samples. Our method relies on the use of a readily accessible ionic liquid electrolyte, tetrabutylphosphonium acetate ([P4444][OAc]):DMSO-d6, for the direct dissolution of biopolymeric samples. We utilize a series of model compounds and apply now classical (nitroxyl-radical and periodate) oxidation reactions to cellulose samples, to allow for accurate resonance assignment, using 2D NMR. Quantitative heteronuclear single quantum correlation (HSQC) was applied in the analysis of key samples to assess its applicability as a high-resolution technique for following cellulose surface modification. Quantitation using HSQC was possible, but only after applying T2correction to integral values. The comprehensive signal assignment of the diverse set of cellulosic species in this study constitutes a blueprint for the direct quantitative structural elucidation of crystalline lignocellulosic, in general, readily available solution-state NMR spectroscopy.Graphic
Herein, we demonstrate the activation of commercial chemical cellulose pulps towards chemical modification by a pre-treatment step with tetrabutylphosphonium acetate ([P4444][OAc]). A heterogeneous (non-dissolving) pre-treatment was applied allowing for a significant reduction in crystallinity, without concomitant formation of the thermodynamically stable cellulose II. An increase in chemical reactivity was demonstrated using two model reactions; (1) acetylation (organic swelling conditions), where high degrees of substitution (DS) were obtained without the need for a catalyst, and (2) 4-acetamido-TEMPO oxidation (aqueous swelling conditions), where significant degrees of oxidation (DO) were obtained, beyond those for the untreated pulps. In both tests a notable improvement in cellulose reactivity was observed. Regioselectivity of acetylation was assessed using 2D NMR for one low and one high DS sample. The low DS showed a small degree of acetylation of the 6-OH, whereas, the high DS from the pre-treated sample showed mainly mixtures of triacetate and diacetates. Important mechanistic information is attained for future development of aqueous and organic-based reactions involving this ionic liquid pre-treatment.
31 July 2018 in Angewandte Chemie International Edition
Ionic liquids are used to dewater a suspension of birch Kraft pulp cellulose nanofibrils (CNF) and as a medium for water‐free topochemical modification of the nanocellulose (a process denoted as “WtF‐Nano”). Acetylation was applied as a model reaction to investigate the degree of modification and scope of effective ionic liquid structures. Little difference in reactivity was observed when water was removed, after introduction of an ionic liquid or molecular co‐solvent. However, the viscoelastic properties of the CNF suspended in two ionic liquids show that the more basic, but non‐dissolving ionic liquid, allows for better solvation of the CNF. Vibrio fischeri bacterial tests show that all ionic liquids in this study were harmless. Scanning electron microscopy and wide‐angle X‐ray scattering on regenerated samples show that the acetylated CNF is still in a fibrillar form. 1 D and 2 D NMR analyses, after direct dissolution in a novel ionic liquid electrolyte solution, indicate that both cellulose and residual xylan on the surface of the nanofibrils reacts to give acetate esters.
We have identified cellulose solvents, comprised of binary mixtures of molecular solvents and ionic liquids that rapidly dissolve cellulose to high concentration and show upper‐critical solution temperature (UCST)‐like thermodynamic behaviour ‐ upon cooling and micro phase‐separation to roughly spherical microparticle particle‐gel mixtures. This is a result of an entropy‐dominant process, controllable by changing temperature, with an overall exothermic regeneration step. However, the initial dissolution of cellulose in this system, from the majority cellulose I allomorph upon increasing temperature, is also exothermic. The mixtures essentially act as ‘thermo‐switchable’ gels. Upon initial dissolution and cooling, micro‐scaled spherical particles are formed, the formation onset and size of which are dependent on the presence of traces of water. Wide‐angle X‐ray scattering (WAXS) and 13C cross‐polarisation magic‐angle spinning (CP‐MAS) NMR spectroscopy have identified that the cellulose micro phase‐separates with no remaining cellulose I allomorph and eventually forms a proportion of the cellulose II allomorph after water washing and drying. The rheological properties of these solutions demonstrate the possibility of a new type of cellulose processing, whereby morphology can be influenced by changing temperature.