31 July 2023 in Journal of Mechatronics, Electrical Power, and Vehicular Technology
Carbon dioxide (CO2) contributes to the greenhouse effect and global warming. The Indonesian government has introduced a reduction in vehicle taxes based on the number of CO2 emissions, meaning that lower CO2 emissions result in lower tax rates. To measure the CO2 emissions, vehicle testing can be conducted on a chassis dynamometer using road load (R/L) parameters to assess the vehicle's loading during the test. The United Nations Economic Commission for Europe (UN ECE) Regulation no. 101 (R101) provides predefined table values for testing, but vehicle manufacturers can also provide their own R/L values, known as actual R/L. In this study, the vehicle underwent two tests: one using the R/L values from the standard table R101 and another using the actual R/L values provided by the manufacturer through coast-down results. By employing the actual R/L values, CO2 emissions can be reduced by up to 7.3 %. This reduction is achieved by lowering the vehicle's load by up to 17 % to enable optimal vehicle performance. Additionally, there is a potential improvement in fuel economy of up to 7.9 % for vehicles. These findings can serve as a reference for establishing future standard testing procedures.
21 March 2026 in International Journal of Hydrogen Energy
11 March 2026 in Applied Soft Computing
23 April 2026 in Scientific Journal of Mechanical Engineering Kinematika
Hydrogen peroxide (H2O2) enrichment is known to enhance combustion efficiency in diesel engines; however, its application as an emulsion is restricted by phase instability in the absence of chemical surfactants. This study investigates the stability and temperature characteristics of non-surfactant emulsions produced using an inline mixer known as the Real-Time Emulsion Supply System (RTES). Four emulsion types were formulated using water and aqueous H2O2 (5-15 vol%) as the dispersed phase, with neat diesel (B0) and biodiesel (B35) serving as the continuous phase: water-in-B0 (WD), H2O2-in-B0 (HD), water-in-B35 (WB), and H2O2-in-B35 (HB). The emulsions were prepared using RTES with a residence time of 180 s. During the preparation, the temperature was continuously recorded using a Graphtec GL840 data logger. The phase separation was monitored over 600 s using a Canon-EM3 camera. Results demonstrate that B35-based emulsions exhibit higher stability compared to B0-based emulsions. The stability tests showed distinct phase separation ratios for each formulation: 12.67% for WD, 10.67% for HD, 4.67% for WB, and 4.27% for HB. Meanwhile, the temperature rise (ΔT) varied slightly by formulation, ranging from 1.67-1.97 °C for WD and HD, and from 2.33-2.73 °C for WB and HB.
7 April 2026 in Scientific Journal of Mechanical Engineering Kinematika
The use of hydrogen peroxide or H2O2 as a fuel additive is known to improve the combustion quality of conventional fuels, including Indonesia’s biodiesel B35. Because H2O2 and B35 do not mix naturally, the H2O2 must be emulsified into B35 to ensure stable fuel delivery and consistent combustion. Conventional emulsification methods typically rely on chemical surfactants, which require a separate preparation step. This study therefore aimed to evaluate the effects of an H2O2–B35 emulsion (HPBE) produced without surfactants on diesel engine performance and emissions. The emulsion was prepared using B35 as the base fuel and 10% (v/v) of 30% aqueous H2O2 as the dispersed phase. Emulsification was carried out using an inline mixer known as the Real-Time Non-Surfactant Emulsion Fuel Supply System (RTES). Engine tests were performed on a Kubota Z482 operating at a constant speed of 2800 rpm under loads of 2.7, 8, 13, 19, and 26 Nm, applied using a Cussons eddy current dynamometer. The parameters measured include Brake Specific Fuel Consumption (BSFC), exhaust gas temperature (EGT) as well as Carbon Monoxide (CO), Carbon Dioxide (CO2), Nitrogen Oxide (NOx) emissions, and smoke opacity. The results showed that, compared to B35, HPBE improved all measured parameters across all loads. BSFC decreased, with the maximum reduction of 22.9% occurring at 8 Nm. At full load, HPBE produced the maximum reductions in smoke opacity (31.3%), CO (29.5%), and CO2 (11.2%). Meanwhile, the maximum NOx reduction of 14.3% was observed at 75% load.