1 December 2011 in Journal of Geotechnical and Geoenvironmental Engineering
Biological processes may provide great and previously unexplored opportunities for cost-effective, in situ improvement of the engineering properties of soil. A laboratory study was conducted to evaluate the changes in geomechanical properties of sand attributable to the formation of calcium precipitates induced through ureolysis catalyzed by Sporosarcina pasteurii (S. pasteurii). Specifically, direct shear and California Bearing Ratio (CBR) tests were conducted on sand specimens subjected to treatment by growing, resting, and dead S. pasteurii cells in completely stirred tank reactors and completely mixed biofilm reactors, respectively. Scanning electron microscopy analyses were also conducted to evaluate microbially induced precipitation. The results of the study show that the bacterial cells effectively improved the geomechanical properties of the sand. Growing cells improved the sand properties owing to microbially induced precipitation and related pore volume changes, whereas dead and resting cells ge...
1 April 2015 in Waste Management
1 April 2013 in Geosynthetics International
Large-scale experiments with cyclic loading were conducted to determine how incorporation of high-density polyethylene (HDPE) geocells affects the rutting properties of working platforms and resilient properties of a subbase in a pavement structure over soft subgrades. Four different geocells were used in this study to reinforce common subbase/base course gravel. Experiments were performed with 225 mm and 450 mm thick unreinforced and reinforced gravel and a crushed rock that is typically used for conventional cut-and-fill working platforms. Experiments were conducted to simulate loading conditions both during construction due to construction equipment and after construction due to traffic conditions over the asphalt pavement once the pavement structure is constructed. Materials used in this study were compacted to 90% relative compaction based on standard Proctor to determine the effect of geocells specifically with gravel material that is compacted to lower than typical standards. Deflections, modulus of subgrade reaction and resilient modulus of each section were evaluated. In summary, presence of geocells reduced the plastic deflection of the working platforms by 30–50%, improved the resilient modulus of the subbase by 40–50%, and the modulus of subgrade reaction by more than 2 times.
26 September 2013 in Road Materials and Pavement Design
Unbound aggregate materials are commonly used in highway bases due to their satisfactory mechanical strength and permeability. Compaction is the most important procedure in highway base construction, thus it is imperative to determine the best compaction method that does not significantly alter the gradation of the aggregates during construction. A laboratory study was undertaken to evaluate the vibratory and impact compaction methods on resilient modulus, bearing capacity, permanent deformation, and hydraulic conductivity characteristics of several aggregates. The results indicated that impact compaction increases fines content of aggregates, resulting in reduced permanent deformation and hydraulic conductivity. Impact compaction usually provides higher resilient modulus and increases the linearity of the resilient modulus curves as compared with vibratory compaction.
1 August 2012 in Journal of Environmental Engineering
One potential beneficial reuse of high-carbon-content (HCC) fly ashes is in reactive barrier applications for remediation of contaminated groundwater. However, leaching of metals from coal fly ashes into the environment is of concern. A series of column leach tests (CLTs) and batch water leach tests (WLTs) were performed to investigate the potential leaching of metals from HCC fly ashes during reactive barrier applications. Fly ash content and pH were two key factors affecting the amount leached in WLTs. Leaching of metals in CLTs exhibited a first flush, followed by a tailing elution pattern, for all fly ashes. Attempts to correlate the WLT and CLT data indicated that scale-up of the WLT results to the column experimental setup provided a better prediction of the leachable amount in CLTs compared with a direct comparison of concentrations. Nevertheless, caution should be exercised when building correlations because of the different testing conditions in the two test setups.
1 December 2018 in Journal of Geotechnical and Geoenvironmental Engineering
The use of industrial by-products in highway embankments is becoming popular due to their large-volume use in such systems. Steel slag is one of these by-products. Previous research shows that steel slag has mechanical properties comparable to those of traditional embankment fill material; however, the environmental impacts of using steel slag need to be carefully evaluated. In this study, a series of sequential water leach and column leach tests are performed in order to assess the trace metal leaching characteristics from pure or treated steel slag highway embankments into surface waters. In addition, a numerical model is used to determine the metal concentrations within the surface waters with respect to distance from the embankment. The results show that placing a clayey embankment soil around pure or treated steel slag significantly decreases the metal concentrations of the leachate. In addition, the numerical model results indicate that, after the slag leachate meets the surface waters, the concentrations decrease to levels significantly lower than the regulatory limits.