Developing vapor phase infiltration (VPI) processes for area selective polymer nanopatterning requires substantial advancement in understanding precursor infiltration, precursor–polymer interaction and process parameters. In this work, infiltration receptive poly(2-vinylpyridine) (P2VP) and poly(4-vinylpyridine) (P4VP) brushes were exposed to a trimethylaluminum (TMA) VPI process and compared to a non-receptive polystyrene (PS) system. The interaction that takes place between TMA and P2VP/P4VP was analysed in detail and we report on notable advantages in the use of P4VP, arising from the difference in position of the pyridinic nitrogen. The VPI process was performed in a commercial atomic layer deposition reactor and the effects of the fundamental process parameters on the three polymer brushes were investigated to ensure optimal area selectivity. In situ X-ray photoelectron spectroscopy (XPS) measurements were supported by grazing angle Fourier transform infrared spectroscopy (GA-FTIR) and hard X-ray photoelectron spectroscopy (HAXPES). The report identifies several important factors when developing a VPI process to ensure area selectivity, while also demonstrating the use of novel pyridine containing polymers for VPI area selective purposes.
Due to its low cost and suitable band gap, silicon has been studied as a photoanode material for some time. However, as a result of poor stability during the oxygen evolution reaction (OER), Si still remains unsuitable for any extended use. Ultra-thin titanium dioxide (TiO2) films have been used as protective coatings and are shown to enhance Si photoanode lifetime with added solar to hydrogen performance improvements through distancing the oxidation reaction away from the Si photoanode surface and improved charge transport through the anode. This study details the nucleation, growth chemistry, and performance of TiO2 thin films prepared via thermal and plasma enhanced atomic layer deposition (ALD) using both titanium isopropoxide and tetrakis(dimethylamido)titanium as the precursor material. The effect of post ALD treatments of plasma and air annealing was also studied. Films were investigated using photoelectrochemical cell testing to evaluate photoelectrochemical performance, and in-vacuum cycle-by-cycle x-ray photoelectron spectroscopy was used as the primary characterisation technique to study nucleation mechanisms and film properties contributing to improvements in cell performance. TiO2 grown by plasma enhanced ALD results in cleaner films with reduced carbon incorporation. However, despite increased carbon incorporation, thermally grown films showed improved photocurrent as a result of oxygen vacancies in these films. Post deposition annealing in a H2 ambient is shown to further improve photocurrent in all cases, while annealing in atmosphere leads to uniform film chemistry and enhanced photocurrent stability in all cases.
8 August 2019 in Journal of Physics D: Applied Physics
In this work we present the results of a hard x-ray photoelectron spectroscopy (HAXPES) study on the creation of metallic copper layers via metal-salt infiltration into a poly-2-vinylpyridine (P2VP) film. Metal salt inclusion is a wet chemistry process which allows for the fabrication of both metal and metal oxide films by means of infiltrating a receptive polymer thin film with metal salt precursors. A copper infiltrated P2VP film was subject to UV/Ozone treatment to form copper oxide and annealed in-vacuo to reduce the film to metallic copper. HAXPES and transmission electron microscope measurements were used to study the polymer film before and after metal salt infiltration, along with analysis of the copper oxide created after UV/Ozone treatment. The results show successful infiltration of the metal salt into the polymer film, as well as complete conversion to copper oxide following UV/Ozone treatment and reduction to metallic copper with a subsequent in situ anneal, which demonstrates the ability of the technique for the creation of several key integrated circuit features.
3 January 2020 in Journal of Physics D: Applied Physics
This work is motivated by the desire to develop a semiconductor device patterning technology based on precursor infiltration into block copolymer materials. Developing an understanding of the preferential infiltration of metal precursors into one of the polymer blocks is of critical importance to advance this patterning approach. In this study, metal salts were used as a means to diffuse metal ions into a poly 2-vinylpyridine (P2vP) polymer brush layer (~4 nm thick) which was deposited by spin coating on a silicon substrate. Thin P2vP films infused with aluminum nitrate and copper nitrate by a wet chemical process were analyzed with angle resolved hard x-ray photoelectron spectroscopy (AR HAXPES). From these photoemission measurements, significant information about the chemical compositional profile of the infiltrated films was obtained. The large sampling depth of HAXPES measurements (20–30 nm) enabled details of the chemical composition of the thin film to be characterized and subsequent angle-resolved HAXPES measurements offered a robust analysis of the interfaces and discrete layers that are present in the films. These measurements displayed evidence of bonding interactions between the elements in the polymer film and the infiltrated salts assisting in the development of an understanding of the infiltration process which needs to be optimized for device fabrication applications. Aluminum nitrate presented more evidence of infiltration into P2vP, while copper nitrate was more predominated at the surfaces into the P2vP.