Karl-Ludwig Krieger

Karl-Ludwig Krieger

Auto-generated profile, based on publicly available information

Karl-Ludwig Krieger

Institute of Electrodynamics and Microelectronics, University of Bremen, Bremen, Germany

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 October 2022 in IEEE Sensors Journal
Verified
Journal Article
Open access
ABAndreas Beering
Andreas Beering
KKKarl-Ludwig Krieger
Karl-Ludwig Krieger
The present work investigates the estimation of rotational speeds based on neural networks and high sampled gearbox vibration data. A total of 18 different network architectures consisting of fully connected network layers, long short-term memory cells and different activation functions are compared. In addition, the impact of the sampling rate of the vibration data, the signal length and the input data type is investigated. Vibration data in the time domain, frequency domain and a combination of both are examined as input data. Finally, the number of neurons is varied to obtain the best possible rotational speed estimation. In order to generate an appropriate dataset for the training of the neural networks, an experimental setup is presented, which is used to record the vibration data of the gearboxes. It becomes apparent that especially vibration data in the frequency domain is suitable for the estimation of the rotational speed. Furthermore, it could be shown that low sampling rates result in an inaccurate speed estimation. Likewise, signal lengths that are too short result in inaccurate estimates. Overall, the speed can be estimated with an accuracy of 7.88 rpm at an average speed of the test data set of 202 rpm.

3 October 2022 in IEEE Access
Verified
Journal Article
Open access
JDJakob Doring
Jakob Doring
JSJulia Scholtyssek
Julia Scholtyssek
ABAndreas Beering
Andreas Beering
KKKarl-Ludwig Krieger
Karl-Ludwig Krieger
Due to the correlation between friction reduction and the road-covering water film height, knowledge about the current wetness level is of relevance for drivers and autonomous systems. A promising approach for wetness quantification is based on capacitive transducer arrays that enable to detect water spray ejected by the tires. Even though previous studies on this approach have shown the feasibility of wetness classification, optimization opportunities exist. While these previous investigations were limited to one feature selection algorithm, we study various algorithms and demonstrate the potential for optimization. Besides an application-specific algorithm that is capable of determining class-dependent features resulting in a performance improvement of more than 0.03 for the considered evaluation metrics, sequential forward floating selection in particular yields the most significant performance increase of more than 0.06. In addition, prior studies were limited to a test track with constrained conditions. Thus, in order to study the transferability of the preceding results, we present investigations on new experimental data acquired on public roads. The unknown and varying environmental conditions on public roads as well as a larger wheel speed range and steering angle effects are shown to significantly decrease classifier performance. We demonstrate that fusing two transducer arrays of different wheel arch liners increases performance by around 0.02. Here, a considerable information benefit can be attributed to the different transducer positions with design-related advantages. Furthermore, we show that the fusion with additional sensor data available in the vehicle results in a further performance improvement of more than 0.02.

12 September 2022 in IEEE Sensors Journal
Verified
Journal Article
Open access
JDJakob Doring
Jakob Doring
LLLukas Lutkehaus
Lukas Lutkehaus
KKKarl-Ludwig Krieger
Karl-Ludwig Krieger
As the friction between a vehicle’s tires and the road surface correlates with the road-covering water film height, knowledge about the present wetness level is of relevance for drivers and autonomous systems. A promising approach for wetness quantification is based on a capacitive transducer array (TA) that is integrated at a front wheel arch liner and capable of detecting spray water ejected by the tires. While this approach has already shown that wetness classification using capacitive measurement data is feasible, potentially affecting factors such as the water’s electrical conductivity were assumed to be constant in the past. This article presents a study on the effect of the spray water’s conductivity on wetness classification for that approach and also demonstrates the feasibility of classifying conductivity using the same capacitive measurement data. For these purposes, we propose a test bench capable of simulating reproducible spray water scenarios. We show the effect of varying conductivity on the measured capacitance curves complicating the distinction of wetness classes. In partial investigations, we demonstrate the extent of the conductivity’s effect on classifier performance. While wetness classification with conductivities differing from training results in poor classifier performance, the mean accuracy (ACC) can be increased to approximately 0.98 considering all occurring conductivities. Furthermore, we propose a two-stage classification approach that initially determines the conductivity and subsequently considers it as an additional feature in wetness classification. The approach increases classifier performance to more than 0.99 indicating that knowledge of the spray’s present conductivity can optimize road surface wetness classification.

16 July 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JSJulia Scholtyssek
Julia Scholtyssek
LBLuka Josephine Bislich
Luka Josephine Bislich
FCFelix Cordes
Felix Cordes
KKKarl-Ludwig Krieger
Karl-Ludwig Krieger
Tapered roller bearings are used partly in very rough and highly stressful environmental conditions. Therefore, the need for condition monitoring is increasing. This study is intended to provide an approach for monitoring bearings in a two-stage planetary gearbox based on vibration analysis. In total, the data of six damage phenomena and one healthy bearing are collected. A convolutional neural network (CNN) is trained and evaluated by using the balanced accuracy. Mainly, it is investigated how many damage severities can be detected. In addition, the robustness of the model regarding unknown speeds and damage phenomena should be proven. The results show a very good differentiation up to all of the presented damage phenomena. The classifier reaches an averaged balanced accuracy of 0.96. Also, samples collected at unknown speeds can be classified well for speed values within the known range. For unknown damage phenomena, the classifier shows limits so that a reliable classification is only applicable with a binary classifier, which differentiates between healthy and damaged. The investigations therefore show that a reliable detection of bearing damage is possible in a two-stage planetary gear. Furthermore, the transferability of the model is successfully tested and implemented for the binary classifier.

28 October 2025 in Smart Agricultural Technology
Verified
Journal Article
Open access
LFLeonard Friedrich
Leonard Friedrich
KKKarl-Ludwig Krieger
Karl-Ludwig Krieger

14 November 2016 in Proceedings
Verified
Conference Paper
Open access
PDF file
JPJoao Pimentel
Joao Pimentel
RKRolf Klemm
Rolf Klemm
MDMünip Dalgic
Münip Dalgic
AIAndree Irretier
Andree Irretier
KKKarl-Ludwig Krieger
Karl-Ludwig Krieger
The detection of structure-borne sound can be used to monitor the structural health of solid structures and machine parts. One way to achieve such an implementation is to place vibroacoustic sensors in contact with the structure. The sensors will typically generate an electric signal in response to the acoustic emissions caused by specific events, such as fractures in the structure. In this paper, vibroacoustic sensors were used to detect structure-borne sound during static tensile testing of metallic samples until complete fracture. The samples used were sections of longitudinal beams made of S700 MC steel. Two different types of piezoelectric sensors were used: PVDF film sensors glued to the sample, and ceramic sensors attached to the sample with a magnet adapter. The bandwidth of the signals was expected from previous studies to be of up to 2 MHz. Simultaneously, force and displacement were measured at the testing machine. An algorithm was written to process the data acquired from the piezo elements and automatically detect relevant events via a simple comparison with a pre-defined voltage threshold to detect signals above the background noise level. The comparison of the detected events with the force measurements from the tensile test showed a very strong correlation between actual fractures (both the initial fracture and its posterior propagation) and the automatic classification carried out by the algorithm. Thus, the vibroacoustic sensor could with little calibration substitute the other standard measurement systems.