16 March 2018 in IEEE Transactions on Power Electronics
This paper presents a unified framework for the modelling, analysis and design of load-independent Class E/EF inverters and rectifiers. These circuits can maintain zero-voltage switching and hence high efficiency for a wide load range without requiring tuning or a feedback loop, and simultaneously achieve a constant AC output or a constant DC output. As switching frequencies are stepping into the MHz region with the use of WBG devices such as GaN, switching loss, implementing fast control loops and current sensing become a challenge which load-independent operation can address. The traditional Class E/EF topologies are presented and the conditions for load-independent operation are derived mathematically, then a thorough analytical characterization of the circuit performance is carried out in terms of voltage and current stresses. Design tables are presented to enable the rapid implementation of these circuits given power and load requirements. Three design examples are presented to showcase the capability of these circuits in enabling efficient and high-power density MHz converters for wireless power transfer (WPT) applications and DC/DC conversion. Specifically, a 150W 13.56MHz ClassEF inverter for WPT, a 150W 10MHz miniature ClassE boost converter, and a lightweight wirelessly powered drone using a 20W 13.56MHz ClassE synchronous rectifier have been designed.
20 September 2018 in IEEE Transactions on Power Electronics
This paper presents the design of a multi-MHz inductive power transfer (IPT) system showcasing lightweight and energy-efficient solutions for non-radiative wireless power transfer. A proof of concept is developed by powering a drone without a battery that can hover freely in proximity to an IPT transmitter. The most challenging aspect, addressed here for the first time, is the complete system level design to provide uninterrupted power-flow efficiently while allowing for variable power demand and highly variable coupling factor. The proposed solution includes the design of lightweight air-core coils that can achieve sufficient coupling without degrading the aerodynamics of the drone, and designing newly-developed resonant power converters at both ends of the system. At the transmittingend, a load-independent Class EF inverter, which can drive a transmitting-coil with constant current amplitude and achieves zero-voltage switching (ZVS) for the entire range of operation, was developed; and at the receiving-end, a hybrid Class E rectifier, which allows tuning for large changes in coupling and power demand, was used. For the demo, the range of motion of the drone was limited by a 7.5 cm nylon string tether, connected between the centre of the transmitting-coil and the bottom of the drone. The design of the IPT system, including all the power conversion stages and the IPT link, is explained in detail. The results on performance and specific practical considerations required for the physical implementation are provided. An average end-to-end efficiency of 60% was achieved for a coupling range of 23% to 5.8%. Relevant simulations concerning human exposure to electromagnetic fields are also included to assure that the demo is safe according to the relevant guidelines. This paper is accompanied by a video featuring the proposed IPT system.
1 November 2014 in IEEE Transactions on Power Electronics
The misalignment and displacement of inductively coupled coils in a wireless power transfer system (WPT) can degrade the power efficiency and limit the amount of power that can be transferred. Coil misalignment leads the primary coil driver to operate in an untuned state which causes nonoptimum switching operation and results in an increase in switching losses. This paper presents a novel method to electronically tune a Class-E inverter used as a primary coil driver in an inductive WPT system to minimize the detrimental effects of misalignment between the inductively coupled coils which may occur during operation. The tuning method uses current-controlled inductors (saturable reactors) and a variable switching frequency to achieve optimum switching conditions regardless of the misalignment. Mathematical analysis is performed on a Class-E inverter based on an improved model of a resonant inductive link. Experimental results are presented to confirm the analysis approach and the suitability of the proposed tuning method.
27 July 2015 in IEEE Transactions on Power Electronics
Class EF and Class E/F inverters are hybrid inverters that combine the improved switch voltage and current waveforms of Class F and Class F-1 inverters with the efficient switching of Class E inverters. As a result, their efficiency, output power and power output capability can be higher in some cases than the Class E inverter. Little is known about these inverters and no attempt has been made to provide an in depth analysis on their performance. The design equations that have been previously derived are limited and are only applicable under certain assumptions. This paper is the first to provide a comprehensive set of analytical analysis of Class EF and Class E/F inverters. The Class EF 2 inverter is then studied in further detail and three special operation cases are defined that allow it to either operate at maximum power-output capability, maximum switching frequency, or maximum output power. Final design equations are provided to allow for rapid design and development. Experimental results are provided to confirm the accuracy of the performed analysis based on a 23-W Class EF 2 inverter at 6.78-MHz and 8.60-MHz switching frequencies. The results also show that the Class EF 2 inverter achieved an efficiency of 91% compared to a 88% efficiency when operated as a Class E inverter.
11 July 2013 in IEEE Transactions on Power Electronics
This paper investigates the performance of Class E inverters used in wireless power transfer applications based on resonant inductive coupling. The variations in the load and the distance between the coils cause Class E inverters to operate under nonoptimal switching conditions, which result in inefficient operation and can lead to permanent damage to its switching transistor. Therefore, a novel approach to tune Class E inverters electronically is proposed. The tuning method relies on saturable reactors to ensure that the inverter operates under optimal switching conditions regardless of variations in the load and the distance between the coils. In addition, a more accurate model of inductive links is presented in order to provide a better understanding of the major power losses in resonant inductive links. Experimental results are presented to confirm the improved accuracy of the inductive link model and the validity of the tuning method.
31 March 2016 in IEEE Transactions on Power Electronics
This paper presents the design and implementation of a Class EF 2 inverter and Class EF 2 rectifier for two -W wireless power transfer (WPT) systems, one operating at 6.78 MHz and the other at 27.12 MHz. It will be shown that the Class EF 2 circuits can be designed to have beneficial features for WPT applications such as reduced second-harmonic component and lower total harmonic distortion, higher power-output capability, reduction in magnetic core requirements and operation at higher frequencies in rectification compared to other circuit topologies. A model will first be presented to analyze the circuits and to derive values of its components to achieve optimum switching operation. Additional analysis regarding harmonic content, magnetic core requirements and open-circuit protection will also be performed. The design and implementation process of the two Class-EF 2 -based WPT systems will be discussed and compared to an equivalent Class-E-based WPT system. Experimental results will be provided to confirm validity of the analysis. A dc-dc efficiency of 75% was achieved with Class-EF 2 -based systems.