18 April 2014 in Journal of Engineering for Gas Turbines and Power
KSKalyan Kumar Srinivasan
+1
This paper presents an experimental analysis of diesel-ignited propane dual fuel low temperature combustion (LTC) based on performance, emissions, and in-cylinder combustion data from a modern, heavy-duty diesel engine. The engine used for these experiments was a 12.9-liter, six-cylinder, direct injection heavy-duty diesel engine with electronic unit diesel injection pumps, a variable geometry turbocharger, and cooled exhaust gas recirculation (EGR). The experiments were performed with gaseous propane (the primary fuel) fumigated upstream of the turbocharger and diesel (the pilot fuel) injected directly into the cylinders. Results are presented for a range of diesel injection timings (SOIs) from 10 deg BTDC to 50 deg BTDC at a brake mean effective pressure (BMEP) of 5 bar and a constant engine speed of 1500 rpm. The effects of SOI, percent energy substitution (PES) of propane (i.e., replacement of diesel fuel energy with propane), intake boost pressure, and cooled EGR on the dual fuel LTC process were investigated. The approach was to determine the effects of SOI while maximizing the PES of propane. Dual fuel LTC was achieved with very early SOIs (e.g., 50 deg BTDC) coupled with high propane PES (>84%), which yielded near-zero NOx (<0.02 g/kW h) and very low smoke emissions (<0.1 FSN). Increasing the propane PES beyond 84% at the SOI of 50 deg BTDC yielded a high COV of IMEP due to retarded combustion phasing (CA50). Intake boost pressures were increased and EGR rates were decreased to minimize the COV, allowing higher propane PES (∼93%); however, lower fuel conversion efficiencies (FCE) and higher HC and CO emissions were observed.
2 May 2014 in Journal of Engineering for Gas Turbines and Power
Diesel-ignited gasoline dual fuel combustion experiments were performed in a single-cylinder research engine (SCRE), outfitted with a common-rail diesel injection system and a stand-alone engine controller. Gasoline was injected in the intake port using a port-fuel injector. The engine was operated at a constant speed of 1500 rev/min, a constant load of 5.2 bar indicated mean effective pressure (IMEP), and a constant gasoline energy substitution of 80%. Parameters such as diesel injection timing (SOI), diesel injection pressure, and boost pressure were varied to quantify their impact on engine performance and engine-out indicated specific nitrogen oxide emissions (ISNOx), indicated specific hydrocarbon emissions (ISHC), indicated specific carbon monoxide emissions (ISCO), and smoke emissions. Advancing SOI from 30 degrees before top dead center (DBTDC) to 60 DBTDC reduced ISNOx from 14 g/kW h to less than 0.1 g/kW h; further advancement of SOI did not yield significant ISNOx reduction. A fundamental change was observed from heterogeneous combustion at 30 DBTDC to “premixed enough” combustion at 50–80 DBTDC and finally to well-mixed diesel-assisted gasoline homogeneous charge compression ignition (HCCI)-like combustion at 170 DBTDC. Smoke emissions were less than 0.1 filter smoke number (FSN) at all SOIs, while ISHC and ISCO were in the range of 8–20 g/kW h, with the earliest SOIs yielding very high values. Indicated fuel conversion efficiencies were ∼ 40–42.5%. An injection pressure sweep from 200 to 1300 bar at 50 DBTDC SOI and 1.5 bar intake boost showed that very low injection pressures lead to more heterogeneous combustion and higher ISNOx and ISCO emissions, while smoke and ISHC emissions remained unaffected. A boost pressure sweep from 1.1 to 1.8 bar at 50 DBTDC SOI and 500 bar rail pressure showed very rapid combustion for the lowest boost conditions, leading to high pressure rise rates, higher ISNOx emissions, and lower ISCO emissions, while smoke and ISHC emissions remained unaffected by boost pressure variations.
1 October 2017 in Journal of Energy Engineering
A 12.9-L heavy-duty (HD) compression ignition engine was operated with diesel-ignited propane. Propane was fumigated into the intake and held a constant 84% of total fuel by energy while diesel was direct-injected at 310 crank angle degrees (CAD). Intake manifold pressure was varied from 135 to 220 kPa (5 to 17.135 psig) for two different exhaust gas recirculation (EGR) valve positions (fully closed and fully open) using a variable nozzle turbo and EGR valve. The engine was operated at a constant speed of 1,500 revolutions per minute (rpm) at constant load of 5 bar brake mean effective pressure (BMEP), which was representative of a typical low load condition for this operating condition (25% full load BMEP). All operating conditions were studied for combustion characteristics, fuel conversion efficiency (FCE), and engine-out emissions. Increasing the intake manifold pressure with a closed EGR valve resulted in lowering brake specific nitrogen oxide emissions (BSNOx) below and also decreased brake specific hydrocarbons emissions (BSHC) with the trade-off of higher brake specific carbon monoxide emissions (BSCO) and lower FCE. Increasing the intake manifold pressure with an open EGR valve increased the BSNOx levels at all conditions but also lowered BSCO and BSHC values while increasing FCE relative to closed EGR-valve conditions. An intake manifold pressure of 168 kPa with negligible EGR levels was shown to result in optimal efficiency and emissions levels while applying EGR at the same intake manifold pressure gave an increase of significant FCE with the cost of little gain in BSNOx.