14 December 2022 in IEEE Electron Device Letters
This work demonstrates vertical Ga2O3 Schottky barrier diodes (SBDs) with a novel junction termination extension (JTE) comprising multiple layers of sputtered p-type nickel oxide (NiO). The NiO layers have the varied lengths to enable a graded decrease in effective charge density away from the main junction. The fabrication of this JTE obviates the etch or implantation and shows good throughput. The fabricated Ga2O3 SBDs exhibit a forward voltage below 1.9 V at the current density of 100 A/cm2, a differential specific on-resistance of 5.9 $\text{m}\Omega \cdot $ cm2, and a breakdown voltage over 2.5 kV. The Baliga’s figure of merit (FOM) exceeds 1 GW/cm2 and is among the highest in multi-kilovolt Ga2O3 SBDs. Besides, the capacitance of the JTE region is extracted, allowing for evaluation of the capacitance, charge, and switching FOM of 1.7 kV-class Ga2O3 SBDs with varied current ratings. The results show good promise of Ga2O3 SBDs for kilovolt power electronics.
8 January 2021 in IEEE Transactions on Power Electronics
Ultrawide-bandgap gallium oxide (Ga 2 O 3 ) devices have recently emerged as promising candidates for power electronics; however, the low thermal conductivity ( k T ) of Ga 2 O 3 causes serious concerns about their electrothermal ruggedness. This letter presents the first experimental demonstrations of large-area Ga 2 O 3 Schottky barrier diodes (SBDs) packaged in the bottom-side-cooling and double-side-cooling configurations, and for the first time, characterizes the surge current capabilities of these packaged Ga 2 O 3 SBDs. Contrary to popular belief, Ga 2 O 3 SBDs with proper packaging show high surge current capabilities. The double-side-cooled Ga 2 O 3 SBDs with a 3 × 3-mm 2 Schottky contact area can sustain a peak surge current over 60 A, with a ratio between the peak surge current and the rated current superior to that of similarly-rated commercial SiC SBDs. The key enabling mechanisms for this high surge current are the small temperature dependence of on -resistance, which strongly reduces the thermal runaway, and the double-side-cooled packaging, in which the heat is extracted directly from the Schottky junction and does not need to go through the low- k T bulk Ga 2 O 3 chip. These results remove some crucial concerns regarding the electrothermal ruggedness of Ga 2 O 3 power devices and manifest the significance of their die-level thermal management.
18 September 2020 in IEEE Journal of the Electron Devices Society
This work, for the first time, experimentally demonstrates a TCAD-Machine Learning (TCAD-ML) framework to assist the analysis of device-to-device variation and operating (ambient) temperature without the need of physical quantities extraction. The ML algorithm used in this work is the Principal Component Analysis (PCA) followed by third order polynomial regression. After calibrated to limited ’expensive’ experimental data’, low cost’ TCAD simulation is used to generate a large amount of device data to train the ML model. The ML was then used to identify the root cause of device variation and operating temperature from any given experimental current-voltage (I-V) characteristics. We applied this framework to study the ultra-wide-bandgap gallium oxide (Ga2O3) Schottky barrier diode (SBD), an emerging device technology that holds great promise for temperature sensing, RF, and power applications in harsh environments. After calibration, over 150,000 electrothermal TCAD simulations are performed with random variation of physical parameters (anode effective work function, drift layer doping, and drift layer thickness) and operating temperature. An ML model is trained using these TCAD data and we found 1,000-10,000 TCAD data can train an accurate machine. We show that without physical quantities extraction, performing PCA is essential for the TCAD trained ML model to be applicable to analyze experimental characteristics. The physical parameters and temperatures predicted by the ML model show good agreement with experimental analysis. Our TCAD-ML framework shows great promise to accelerate the development of new device technologies with a significantly more efficient process of material and device experimentation.
5 August 2020 in IEEE Access
A machine learning (ML) model by combing two autoencoders and one linear regression model is proposed to avoid overfitting and to improve the accuracy of Technology Computer-Aided Design (TCAD)-augmented ML for semiconductor structural variation identification and inverse design, without using domain expertise. TCAD-augmented ML utilizes TCAD simulations to generate sufficient data for ML model development when experimental data are inadequate. The ML model can then be used to identify semiconductor structural variation for given experimental electrical measurements. In this study, the variation of layer thicknesses in the p-i-n diode is used as a demonstration. An ML model is developed to predict the diode layer thicknesses based on a given Current-Voltage (IV) curve. Although the variations of interest can be incorporated easily in TCAD simulations to generate ML training data, the TCAD-augmented ML model generally is overfitted and cannot predict the variations in experiment well due to hidden variables which also alters the IV curves. We show that by using an autoencoder, this problem can be solved. To verify the effectiveness, another set of TCAD simulation data is generated with hidden variables (dopant concentration variation) to emulate experimental data. Testing on the second set of data shows that the proposed model can avoid overfitting and has up to 15 times improvement in accuracy in thickness prediction. Moreover, this model is used successfully to perform inverse design and can capture an underlying physics that cannot be described by a simple physical parameter.
29 April 2021 in IEEE Transactions on Electron Devices
In this article, using experimental data, we demonstrate that the technology computer-aided design (TCAD) is a very cost-effective tool to generate the data to build machine learning (ML) models for semiconductor device and process characterization. Characterization of the emerging ultra wide bandgap gallium oxide (Ga₂O₃) Schottky barrier diode (SBD) is used as an example. Machines are trained by using only TCAD I-V's and then used to deduce the effective Schottky metal work function (WF) and ambient temperature (T) of an experimental SBD based on its I-V. Besides noise, the experimental device also suffers from relatively large variations in drift layer thickness and doping concentrations. Both ML models with domain expertise (WDE) and without domain expertise (WoDE) are studied and compared. The ML model WDE requires the use of device knowledge to extract relevant features (e.g., subthreshold slope and turn-on voltage) for ML. The ML model WoDE obviates such a requirement and can be extended to cases where domain expertise is difficult to apply. Denoising autoencoder is used in the WoDE case. We showed that with only 500 TCAD I-V's, we can train machines WDE and WoDE that can deduce the experimental device WF and T reasonably well. In particular, the ML model WoDE has an acceptable prediction accuracy despite the noise and additional variations in the experimental device.
14 June 2021 in IEEE Electron Device Letters
The low thermal conductivity of Ga 2 O 3 has arguably been the most serious concern for Ga 2 O 3 power and RF devices. Despite many simulation studies, there is no experimental report on the thermal resistance of a large-area, packaged Ga 2 O 3 device. This work fills this gap by demonstrating a 15-A double-side packaged Ga 2 O 3 Schottky barrier diode (SBD) and measuring its junction-to-case thermal resistance ( R θJC ) in the bottom-side- and junction-side-cooling configurations. The R θJC characterization is based on the transient dual interface method, i.e., JEDEC 51-14 standard. The R θJC of the junction- and bottom-cooled Ga 2 O 3 SBD was measured to be 0.5 K/W and 1.43 K/W, respectively, with the former R θJC lower than that of similarly-rated commercial SiC SBDs. This low R θJC is attributable to the heat extraction directly from the Schottky junction instead of through the Ga 2 O 3 chip. The R θJC lower than that of commercial SiC devices proves the viability of Ga 2 O 3 devices for high-power applications and manifest the significance of proper packaging for their thermal management.