23 January 2021 in ACM Transactions on Sensor Networks
Heart rate (HR) estimation based on photoplethysmography (PPG) signals has been widely adopted in wrist-worn devices. However, the motion artifacts caused by the user’s physical activities make it difficult to get the accurate HR estimation from contaminated PPG signals. Although many signal processing methods have been proposed to address this challenge, they are often highly optimized for specific scenarios, making them impractical in real-world settings where a user may perform a wide range of physical activities. In this article, we propose DeepHeart, a new HR estimation approach that features deep-learning-based denoising and spectrum-analysis-based calibration. DeepHeart generates clean PPG signals from electrocardiogram signals based on a training data set. Then a set of denoising convolutional neural networks (DCNNs) are trained with the contaminated PPG signals and their corresponding clean PPG signals. Contaminated PPG signals are then denoised by an ensemble of DCNNs and a spectrum-analysis-based calibration is performed to estimate the final HR. We evaluate DeepHeart on the IEEE Signal Processing Cup training data set with 12 records collected during various physical activities. DeepHeart achieves an average absolute error of 1.61 beats per minute (bpm), outperforming a state-of-the-art deep learning approach (4 bpm) and a classical signal processing approach (2.34 bpm).
3 November 2014 in IEEE Transactions on Consumer Electronics
Many consumer products in the home environment are managed by the Wireless Sensor Networks (WSNs). However, the energy hole problem in the WSNs which with logical ring topology and uniformly distributed sensors is usually caused by the energy exhaustion of the sensors which distributed in the first radius range of the sink. This paper firstly analyzed the energy consumption model of the sensor, the data transmission model of the sensor, and the energy consumption distribution model of the WSNs. Then, a WSN Energy Hole Alleviating (WSNEHA) algorithm, which is based on the data forwarding and router selection strategy, is proposed. The WSNEHPA adopts the data forwarding and routing selection strategy to balance the energy consumption of the sensors in the first radius range of the sink. Experimental results demonstrate that WSNEHPA can efficiently balance the energy consumption of the sensors in the first radius range of the sink, and that the lifetime of the WSNs can be extended efficiently.
21 July 2020 in ACM Transactions on Sensor Networks
The quality of sleep is an important factor in maintaining a healthy life style. A great deal of work has been done for designing sleep monitoring systems. However, most of existing solutions bring invasion to users more or less due to the exploration of the accelerometer sensor inside the device. This article presents iSleep—a practical system to monitor people’s sleep quality using off-the-shelf smartphone. iSleep uses the built-in microphone of the smartphone to detect the events that are closely related to sleep quality, and infers quantitative measures of sleep quality. iSleep adopts a lightweight decision-tree-based algorithm to classify various events. For two-user scenario, iSleep differentiates the events of two users either when two phones can collaborate with each other or when two phones cannot communicate with each other. The experimental results show that iSleep achieves consistently above 90% accuracy for event classification in a variety of different settings in one-user scenario and above 92% accuracy for distinguishing users in two-user scenario. By providing a fine-grained sleep profile that depicts details of sleep-related events, iSleep allows the user to track the sleep efficiency over time and relate irregular sleep patterns to possible causes.
4 March 2021 in IEEE Internet of Things Journal
Continuous and accurate respiratory volume monitoring is crucial in many healthcare-related applications. Traditional respiratory volume monitoring approaches involve obtrusive devices that are uncomfortable for long-term monitoring, while unobtrusive approaches mainly focus on sensing the respiratory rate, which is insufficient for many healthcare-related applications. In this article, we present radio-frequency respiratory volume monitoring (RF-RVM), an unobtrusive system to sense the respiratory volume based on commercial off-the-shelf (COTS) RFID devices. Specifically, RF-RVM continuously collects the temporal phase information from tags attached to the chest and abdomen to extract the chest displacement and abdomen displacement caused by respiration. Then, we assess the respiratory volume by training a backpropagation neural network model to correlate chest and abdomen displacements and respiratory volume. We use a reference tag attached under the user's neck to eliminate the noise caused by slight movements of the upper body during respiration. We implement and evaluate RF-RVM based on COTS RFID devices. The experimental results show that RF-RVM can continuously monitor user's respiratory volume with an average accuracy of 94.52% for leave-one-session-out cross-validation and 91.96% for leave-one-record-out cross-validation based on a data set sampled from 20 volunteers.
16 August 2021 in IEEE/ACM Transactions on Networking
Recent years have seen a widespread deployment of NB-IoT networks for massive machine-to-machine communication in the emerging 5G era. Unfortunately, the key aspects of NB-IoT networks, such as radio access performance and power consumption have not been well-understood due to lack of effective tools and closed nature of operational cellular infrastructure. In this paper, we develop NB-Scope - the first hardware NB-IoT diagnostic tool that supports fine-grained fusion of power and protocol traces. We then conduct a large-scale field measurement study consisting of 30 nodes deployed at over 1,200 locations in 4 regions during a period of three months. Our in-depth analysis of the collected 49 GB traces showed that NB-IoT nodes yield significantly imbalanced energy consumption in the wild, up to a ratio of 75:1, which may lead to short battery lifetime and frequent network partition. Such a high performance variance can be attributed to several key factors including diverse network coverage levels, long tail power profile, and excessive control message repetitions. We then explore the optimization of NB-IoT base station settings on a software-defined eNodeB testbed, and suggest several important design aspects that can be considered by future NB-IoT specifications and chipsets.
25 August 2021 in IEEE Internet of Things Journal
Narrowband Internet of Things (NB-IoT) standardized by the 3GPP has attracted significant attention since its appearance. It provides extended coverage, high capacity, reduced device processing complexity, and low-power consumption to meet the requirements of a wide range of IoT applications. In particular, NB-IoT is expected to bring IoT devices prolonged lifetime up to ten years. Radio access (RA) plays a key role in the total power consumption of NB-IoT devices. Specifically, the enhanced coverage levels (ECLs) configure the user equipment (UE) with different random-access resources and power consumption during packet transmissions. In this article, we examine the ECL selection strategies for reducing the power consumption of NB-IoT. We develop two testbeds to conduct extensive field measurements related to ECL selection. Based on the measurement results, we analyze the key issues in the ECL selection process. Then, we propose an adaptive RA approach for UE, which includes two novel strategies for predictive ECL selection and opportunistic packet transmission. Evaluations show that, with the configuration of ECL selected by our adaptive approach, the UE can reduce the radio power consumption up to 36% while maintaining the same block error rate (BLER) during uploading under real-world settings.